From: Maxim Shchetynin <maxim@de.ibm.com>
Reopen a remote port only if the link-test fails. This avoids that a
port is unnecessarily reopened.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Extend the time for adapter initialization: In case of protocol
status HOST_CONNECTION_INITIALIZING for the exchange config data
command do a first retry in 1 second, then double the sleep time for
each following retry until recovery exceeds 2 minutes. The old
behaviour of allowing 6 retries with .5 seconds delay between retries
was insufficient and qdio queues were shut down too erarly.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes the handling of failed requests for GID_PN nameserver command:
Set ZFCP_STATUS_PORT_INVALID_WWPN only if indicated by response
payload for GID_PN nameserver command and not if fsf request fails.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- the eisa layer only probes when it's actually safe, no need for
a driver option
- store the id table directly in linux format instead of convering
at runtime
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
there's absolutely no reason not to trust the driver private data
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removes the rarely used "flags_dump" mechanism of zfcp.
Equivalent debug information will be provided with a reworking of
zfcp's s390dbf-facilities which is in preparation.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch removes our homegrown DMA masks and uses the ones defined in the kernel.
This patch replaces the broken one I sent in earlier. It has been tested and works. Please discard the first submission.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds some files into the /sys/class/scsi_host/hostN
directories for aacraid adapters:
model
vendor
hba_kernel_version
hba_monitor_version
hba_bios_version
serial_number
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are several extra things that have to be considered when running
Domain Validation on a u320 target (notably how you fall back).
Hopefully this should help us when someone adds this transport class to
aic79xx.
I've tested this on the lsi1030, so I know it works correctly up to
u320.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For setting coupled parameters, we need to be comparing against the goal
settings, not the current ones.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A problem exists todayin the sg driver that if an SG_IO request is
outstanding to a device when it is removed from the system. The
system may oops if that command completes later in time.
1. sg_remove gets called
2. sg_remove calls sg_finish_req_req on all pending requests
This removes the Sg_request's from the headrp list in the Sg_fd
3. The sleeping SG_IO ioctl is woken. It does nothing and returns.
4. The caller closes the fd, which invokes sg_release
5. sg_release calls sg_remove_sfp. It finds no outstanding commands
since the headrp list is empty, so it calls __sg_remove_sfp,
which frees the sfp.
6. Now when sg_cmd_done gets called, sg uses upper_private_data in
the Scsi_Request, which should point to the srp, which has been
freed, so it points to freed memory.
7. sg then dereferences the srp pointer to get the sfp, and we oops.
The fix is to NULL out the upper_private_data field in this path,
which sg_cmd_done already checks for, which will prevent the oops
from occurring.
cpu 0x1: Vector: 300 (Data Access) at [c00000000fff7aa0]
pc: d0000000002bbea8: .sg_cmd_done+0x70/0x394 [sg]
lr: d000000000073304: .scsi_finish_command+0x10c/0x130 [scsi_mod]
sp: c00000000fff7d20
msr: 8000000000009032
dar: 2f70726f63202f78
dsisr: 40000000
current = 0xc0000000024589b0
paca = 0xc0000000003da800
pid = 7, comm = events/1
[c00000000fff7dc0] d000000000073304 .scsi_finish_command+0x10c/0x130 [scsi_mod]
[c00000000fff7e50] d00000000007317c .scsi_softirq+0x140/0x168 [scsi_mod]
[c00000000fff7ef0] c0000000000634dc .__do_softirq+0xa0/0x17c
[c00000000fff7f90] c000000000018430 .call_do_softirq+0x14/0x24
[c00000000ed472e0] c0000000000142e0 .do_softirq+0x74/0x9c
[c00000000ed47370] c000000000013c9c .do_IRQ+0xe8/0x100
[c00000000ed473f0] c00000000000ae34 HardwareInterrupt_entry+0x8/0x54
c00000000003df28 .smp_call_function+0
x100/0x1d0
[c00000000ed47780] c0000000000ba99c .invalidate_bh_lrus+0x30/0x70
[c00000000ed47810] c0000000000b91a0 .invalidate_bdev+0x18/0x3c
[c00000000ed478a0] c0000000000da7b8 .__invalidate_device+0x70/0x94
[c00000000ed47930] c0000000001d40bc .invalidate_partition+0x4c/0x7c
[c00000000ed479c0] c00000000010a944 .del_gendisk+0x48/0x15c
[c00000000ed47a50] d00000000003d55c .sd_remove+0x34/0xe4 [sd_mod]
[c00000000ed47ae0] c0000000001c5d30 .device_release_driver+0x90/0xb4
[c00000000ed47b70] c0000000001c6130 .bus_remove_device+0xb0/0x12c
[c00000000ed47c00] c0000000001c4378 .device_del+0x120/0x198
[c00000000ed47ca0] d00000000007dcdc .scsi_remove_device+0xb4/0x194 [scsi_mod]
[c00000000ed47d30] d0000000000a5864 .ipr_worker_thread+0x1d4/0x27c [ipr]
[c00000000ed47dd0] c0000000000734c4 .worker_thread+0x238/0x2f4
[c00000000ed47ee0] c0000000000796c0 .kthread+0xcc/0x11c
[c00000000ed47f90] c000000000018ad0 .kernel_thread+0x4c/0x6c
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since the aic driver is now taught to speak in terms of the generic
linux devices, we can now also dispense with the transport class get
routines (since we update the parameters when the driver sees they
change) and also plumb it into the spi transport transfer agreement
reporting infrastructure.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch basically allows any HBA attached to the SPI transport class
to declare an extra area which the mid-layer will allocate as part of
its device and target allocations.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/ieee1394/sbp2.c: In function `sbp2_check_sbp2_response':
drivers/ieee1394/sbp2.c:2154: warning: unused variable `device_type'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This gives the HBA driver notice when a target is created and
destroyed to allow it to manage its own target based allocations
accordingly.
This is a much reduced verson of the original patch sent in by
James.Smart@Emulex.com
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Marcello Maggioni <hayarms@gmail.com>
Problem: Some drives (NEC 3500, TDK 1616N, Mad-dog MD-16XDVD9, RICOH
MP5163DA, Memorex DVD9 drive and IO-DATA's too for sure), if a
CD/DVD is inserted into the tray when the system is booted and if
before the OS bootup the BIOS checked for the presence of a bootable
CD/DVD into the drive, during the IDE probe phase the drive may
result busy and remain so for the next 25/30 seconds . This cause the
drive to be skipped during the booting phase and not begin usable
until the next reboot (if the reboot goes well and the drive doesn't
timeout again).
Solution: Rising the timeout time from 10 seconds to 35 seconds
(during these 35 seconds every drive should wake up for sure
according to the tests I've done).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
a) TYPE_SDAD renamed to TYPE_RBC and taken to scsi.h
b) in sbp2.c remapping of TYPE_RPB to TYPE_DISK turned off
c) relevant places in midlayer and sd.c taught to accept TYPE_RBC
d) sd.c::sd_read_cache_type() looks into page 6 when dealing with
TYPE_RBC - these guys have writeback cache flag there and are not guaranteed
to have page 8 at all.
e) sd_read_cache_type() got an extra sanity check - it checks that
it got the page it asked for before using its contents. And screams if
mismatch had happened. Rationale: there are broken devices out there that
are "helpful" enough to go for "I don't have a page you've asked for, here,
have another one". For example, PL3507 had been caught doing just that...
f) sbp2 sets sdev->use_10_for_rw and sdev->use_10_for_ms instead
of bothering to remap READ6/WRITE6/MOD_SENSE, so most of the conversions
in there are gone now.
Incidentally, I wonder if USB storage devices that have no
mode page 8 are simply RBC ones. I haven't touched that, but it might
be interesting to check...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sym2 version 2.2.1:
- Fix MMIO BAR detection (Thanks to Bob Picco)
- Fix odd-sized transfers with a wide bus (Thanks to Larry Stephens)
- Write posting fixes (Thanks to Thibaut Varene)
- Change one of the GFP_KERNEL allocations back into a GFP_ATOMIC
- Make CCB_BA() return a script-endian address
- Move range checks and disabling of devices from the queuecommand path
to slave_alloc()
- Remove a warning in sym_setup_cdb()
- Keep a pointer to the scsi_target instead of the scsi_dev in the tcb
- Remove a check for the upper layers passing an oversized cmd
- Replace CAM_REQ_ constants with the Linux DID_ constants
- Replace CAM_DIR_ constants with the Linux DMA_ constants
- Inline sym_read_parisc_pdc() on non-parisc systems
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Stuart Hayes <Stuart_Hayes@dell.com>
The system can panic with a null pointer dereference using ide-scsi if
PIO is being done on scatter gather pages that are in high memory,
because page_address() returns 0. We are actually seeing this using a
tape drive. This patch will kmap_atomic() the pages before performing
PIO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
* add ide_bus_match() and export ide_bus_type
* split ide_remove_driver_from_hwgroup() out of ide_unregister()
* move device cleanup from ide_unregister() to drive_release_dev()
* convert ide_driver_t->name to driver->name
* convert ide_driver_t->{attach,cleanup} to driver->{probe,remove}
* remove ide_driver_t->busy as ide_bus_type->subsys.rwsem
protects against concurrent ->{probe,remove} calls
* make ide_{un}register_driver() void as it cannot fail now
* use driver_{un}register() directly, remove ide_{un}register_driver()
* use device_register() instead of ata_attach(), remove ata_attach()
* add proc_print_driver() and ide_drivers_show(), remove ide_drivers_op
* fix ide_replace_subdriver() and move it to ide-proc.c
* remove ide_driver_t->drives, ide_drives and drives_lock
* remove ide_driver_t->drivers, drivers and drivers_lock
* remove ide_drive_t->driver and DRIVER() macro
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
When testing ATAPI PIO data transfer on the ppc64 platform, __atapi_pio_bytes() got zero when
sg_dma_len() is used. I checked the <asm-ppc64/scatterlish.h>, the struct scatterlist is defined as:
struct scatterlist {
struct page *page;
unsigned int offset;
unsigned int length;
/* For TCE support */
u32 dma_address;
u32 dma_length;
};
#define sg_dma_address(sg) ((sg)->dma_address)
#define sg_dma_len(sg) ((sg)->dma_length)
So, if the scatterlist is not DMA mapped, sg_dma_len() will return zero on ppc64.
The same problem should occur on the x86-64 platform.
On the i386 platform, sg_dma_len() returns sg->length, that's why the problem does not occur on an i386.
Changes:
- Use sg->length if the scatterlist is not DMA mapped (yet).
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
This patch shows the correct locations of the heat sensors present in iBook
and PowerBooks G4, instead of displaying them as being on CPU and GPU
(which is not always the case).
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch limits therm_adt746x to currently existing fan controllers in
Apple laptops. It may avoid problems with future hardware.
Signed-off-by: Colin Leroy <colin@colino.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make MTU field in SA PathRecord and MCMemberRecord a u8 rather than an enum
to avoid complications with endianness.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free all unclaimed MAD receive buffers when userspace closes our file so we
don't leak memory.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check if a client passes a NULL callback into an SA query, and if so, never
call back. This fixes an oops if someone unloads ib_ipoib and ib_sa in
rapid succession. ib_ipoib does an MCMember delete with a NULL callback
and 0 timeout on unload, which is usually fine since the delete completes
successfully. However, if ib_sa is unloaded immediately afterwards, the
delete will be canceled and ib_sa will try to call the (now already
unloaded) ib_ipoib module back with the cancel completion, which triggers
the oops.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like the recent IPMI patches had some -mm-onlyisms.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't try to access the i2c bus if the register wasn't successful.
Signed-off-by: Gerd Knorr <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has been sitting for a while, and is causing lots of grief for
people burning CDs. It relaxes the dma restriction for ide-cd,
requiring only the length to be 32-byte aligned, address should be fine
at normal double word alignment.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a bigger Speedtouch update coming your way after 2.6.12 but in
the meantime, let's at least make it automatically resync if the DSL
signal is lost.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For quite a while, there has existed a hypervisor bug on legacy iSeries
which means that we do not get the boot time set in the kernel. This
patch works around that bug. This was most noticable when the root
partition needed to be checked at every boot as the kernel thought it
was some time in 1905 until user mode reset the time correctly.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On PPC64, we keep track of when we need to update jiffies (and the
variables used to calculate the time of day) based on the time base.
If the time base frequence is sufficiently high compared to the
processor clock frequency, then it is possible for the time of day
variables to be corrupted at the time of the first decrementer interrupt
we take. This became obvious on a legacy iSeries where the time base
frequency is the same as the processor clock.
This one line patch fixes the initialisation so that the time of day
variables and the indicator we use to tell when updates are due are
better synchronised.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
