IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When SuperH CPU has IRQ multi of DMAC, SH_DMA_IRQ_MULTI becomes enable.
The following CPU's are Multi IRQ of DMAC now.
- SH775X and SH7091
- SH776X
- SH7780
- SH7785
If SH_DMA_IRQ_MULTI becomes enable, dma-sh api driver is optimized
for Multi IRQ.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.
Disable it out for non-SH4 builds.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements preliminary suspend/resume support for the PMB.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work a PCI device when 32-bit physical
address mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d7) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was accidentally dropped in the multiple vectors per irq conversion.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the recent entry.S refactoring, the SH-X3 path had a mov.l for a
register to register copy, resulting in:
AS arch/sh/kernel/cpu/sh4/../sh3/entry.o
arch/sh/kernel/cpu/sh4/../sh3/entry.S: Assembler messages:
arch/sh/kernel/cpu/sh4/../sh3/entry.S:366: Error: invalid operands for opcode
make[3]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
Switch it over to a mov to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7785 hardware
blocks such as SCIF/DMAC/PCIC5/MMCIF/GDTA/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
