In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't have any use for these machvec fixups anymore, kill them all
off and go with the generic instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables the SM501 drivers for the R2D board. Additional
work needs to be done to migrate off of the VoyagerGX cchip
code to make use of the rest of the mfd infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I run a preemptive kernel-2.6.20 for SH7780, a created
kthread(pdflush) can not exit by do_exit() in kernel_thread_helper. I
think that the created kthread should have a room for 'struct pt_regs'
space on the stack top, because __switch_to() will refer to the space as
follows using 'regs = task_pt_regs(prev)' and next condition may be true.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a missing return in do_signal() that caused the saved
sigmask to be written back after having successfully delivered
the signal.
Signed-off-by: Ryusuke Sakato <sakato@hsdv.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This takes care of tearing down the UBC so it's not inadvertently
left configured at the next context switch time. Failure to do
this results in spurious SIGTRAPs in certain debug sequences.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Adds cardbus ressources for MTX1 boards which have a PCMCIA controller.
Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has removed unused timer resource.
Moreover, the name of reserved resources ware changed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If R4k counter was used for hpt_timer and interrupt source,
c0_hpt_timer_init() initializes the c0_compare register.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to stop tc35815 before resetting the board. This fixes the
build of tc35815 as a module. This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We mistakedly modify 'bus' in the innermost loop. What
should happen is that at each register index iteration,
we start with the same 'bus'.
So preserve it's value at the top level, and use a loop
local variable 'dbus' for iteration.
This bug causes registers other than the first to be
decoded improperly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update help text with location of documentation
and duplicate the note on the speed of CRC
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always allow backtrace when using oprofile on ARM, even if a PMU
isn't present.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing includes to board-nokia770 to make it
compile again.
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.
This one-liner fixe the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Teach OMAP2 gp timer that HZ isn't always 100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No IRQF_TRIGGER set_type function for IRQ 353 (MPUIO)
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes serial usable also on omap310, not only 1510.
(changing 1510->15xx)
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When it goes to free1_out, dev->dma_mem has not been freed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3: Introduce CONFIG_PS3_ADVANCED, as suggested by Roman Zippel, and use
it to control questions about PS3 subsystems that may not be obvious for
the casual user.
This gets rid of the following warning on non-powerpc platforms: |
drivers/video/Kconfig:1604:warning: 'select' used by config symbol 'FB_PS3'
refer to undefined symbol 'PS3_PS3AV'
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a problem seen by a number of people running UML on newer host
kernels. init would hang with an infinite segfault loop.
It turns out that the host kernel was providing a AT_SYSINFO_EHDR of
0xffffe000, which faked UML into believing that the host VDSO page could be
reused. However, AT_SYSINFO pointed into the middle of the address space, and
was unmapped as a result. Because UML was providing AT_SYSINFO_EHDR and
AT_SYSINFO to its own processes, these would branch to nowhere when trying to
use the VDSO.
The fix is to also check the location of AT_SYSINFO when deciding whether to
use the host's VDSO.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the RAW device driver options to the UML Kconfig.char file so that you may
use them in UML.
Signed-off-by: Allan Graves<allan.graves@gmail.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the 2.6.20 hang patch, I accidentally threw out an error message.
This puts it back.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some locking to host_ldt_entries to prevent racing when reading LDT
information from the host.
The locking is somewhat more careful than my previous attempt. Now, only
the check of host_ldt_entries is locked. The lock is dropped immediately
afterwards, and if the LDT needs initializing, that (and the memory
allocations needed) proceed outside the lock.
Also fixed some style violations.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FRV does not require a ZONE_DMA, so all DMA'able pages that aren't highmem
should be in ZONE_NORMAL.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_ALIGNMENT_TRAP is never set on arm26.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To provide compatibilty with SN kernels that do and do not
have ACPI IO support, the SN PROM must build different
versions of some ACPI tables based on which kernel is booting.
As such, the tables may have to change at kernel boot time.
By default, prior to kernel boot, the PROM builds an empty
DSDT (header only) and no SSDTs. If an ACPI capable kernel
boots, the kernel will notify the PROM, at platform setup time,
and the PROM will build full DSDT and SSDT tables.
With the latest changes to acpi_table_init(), the table lengths
are saved, and when our PROM changes them, the changes are not seen,
and the kernel will crash on boot. Because of issues with kexec support,
we are not able to create the tables prior to acpi_table_init().
As a result, we are making a second call to acpi_table_init() to
process the rebuilt DSDT and SSDTs.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When removing set_native_irq I missed the fact that it was
called in a couple of places that were compiled even when
SMP support is disabled. And since the irq_desc[].affinity
field only exists in SMP things broke.
Thanks to Simon Arlott <simon@arlott.org> for spotting this.
There are a couple of ways to fix this but the simplest one
is to just remove the assignments. The affinity field is only
used to display a value to the user, and nothing on either i386
or x86_64 reads it or depends on it being any particlua value,
so skipping the assignment is safe. The assignment that
is being removed is just for the initial affinity value before
the user explicitly sets it. The irq_desc array initializes
this field to CPU_MASK_ALL so the field is initialized to
a reasonable value in the SMP case without being set.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the PCI controller OBP node lacks an interrupt-map
and interrupt-map-mask property, we need to form the
INO by hand. The PCI swizzle logic was not doing that
properly.
This was a regression added by the of_device code.
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_cpus_done is too early for us... before we even do a device
inventory! Move update_cr16_clocksource into the tail end of
processor_probe() and stub it out on CONFIG_SMP=n builds.
Verified that clocksource0 is properly updated to use jiffies
on an SMP build.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
So move the code to be called by smp_cpus_done, which is
after we've figured out if there's more than one cpu
actually present.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Use MIPS_CPU_IRQ_BASE instead of own define.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibios_fixup_device_resources() is called by pcibios_fixup_bus() which is
marked as __devinit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Many Makefiles in arch/mips have EXTRA_AFLAGS := $(CFLAGS) line. This
is redundant while AFLAGS contains $(cflags-y) and any options only
listed in CFLAGS (not in cflags-y) should be unnecessary for asm
sources.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit aeeddc1435, which was
half-baked and broken. It just resulted in compile errors, since
cpufreq_register_driver() still changes the 'driver_data' by setting
bits in the flags field. So claiming it is 'const' _really_ doesn't
work.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge suggested the use of -freg-struct-return, which does
structure-returns (such as when using pte_t) in registers instead of on
the stack.
that is indeed so, and this option reduced the kernel size a bit:
text data bss dec hex filename
4799506 543456 3760128 9103090 8ae6f2 vmlinux.before
4798117 543456 3760128 9101701 8ae185 vmlinux.after
the resulting kernel booted fine on my testbox. Lets go for it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix port 0 mac address for mips mv6434x platforms
[SERIAL] serial_txx9 driver update
Revert "[PATCH] Generic ioremap_page_range: mips conversion"
[MIPS] Cobalt: Rename "Colo" MTD partition to "firmware".
[MIPS] SMP: Get smp_tune_scheduling to do something useful.
[MIPS] Add basic SMARTMIPS ASE support
The problem: After moving an interrupt when is it safe to teardown
the data structures for receiving the interrupt at the old location?
With a normal pci device it is possible to issue a read to a device
to flush all posted writes. This does not work for the oldest ioapics
because they are on a 3-wire apic bus which is a completely different
data path. For some more modern ioapics when everything is using
front side bus delivery you can flush interrupts by simply issuing a
read to the ioapic. For other modern ioapics emperical testing has
shown that this does not work.
So it appears the only reliable way to know the last of the irqs from an
ioapic have been received from before the ioapic was reprogrammed is to
received the first irq from the ioapic from after it was reprogrammed.
Once we know the last irq message has been received from an ioapic
into a local apic we then need to know that irq message has been
processed through the local apics.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the ISA irqs we reserve 16 vectors. This patch adds constants for
those vectors and modifies the code to use them. Making the code a
little clearer and making it possible to move these vectors in the future.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code in io_apic.c and in i8259.c currently hardcode the same
vector for the timer interrupt so there is no reason for a special
assignment for the timer as the setup for the i8259 already takes care
of this.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently assign_irq_vector works mostly by side effect and returns
the results of it's changes to the caller. Which makes for a lot of
arguments to pass/return and confusion as to what to do if you need
the status but you aren't calling assign_irq_vector.
This patch stops returning values from assign_irq_vector that can be
retrieved just as easily by examining irq_cfg, and modifies the
callers to retrive those values from irq_cfg when they need them.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the io_apic.c has several parallel arrays for different
kinds of data that can be know about an irq. The parallel arrays
make the code harder to maintain and make it difficult to remove
the static limits on the number of the number of irqs.
This patch pushes irq_data and irq_vector into a irq_cfg array and
updates the code to use it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NR_IRQ_VECTORS is currently a compatiblity define set to NR_IRQs.
This patch updates the users of NR_IRQ_VECTORS to use NR_IRQs instead
so that NR_IRQ_VECTORS can be removed.
There is still shared code with arch/i386 that uses NR_IRQ_VECTORS
so we can't remove the #define just yet :(
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have an irq that comes from multiple io_apic pins the FINAL action
(which is io_apic_sync or nothing) needs to be called for every entry or
else if the two pins come from different io_apics we may not wait until
after the action happens on the io_apic.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the code has been picking TARGET_CPUS when asked to
set the affinity to an empty set of cpus. That is just silly it's
extra work. Instead if there are no cpus to set the affinity to we
should just give up immediately. That is simpler and a little more
intuitive.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have two routines that do practically the same thing
setup_IO_APIC_irq and io_apic_set_pci_routing. This patch makes
setup_IO_APIC_irq the common factor of these two previous routines.
For setup_IO_APIC_irq all that was needed was to pass the trigger
and polarity to make the code a proper subset of io_apic_set_pci_routing.
Hopefully consolidating these two routines will improve maintenance
there were several differences that simply appear to be one routine
or the other getting it wrong.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By precomputing old_mask I remove an extra if statement, remove an
indentation level and make the code slightly easier to read.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2ff2d3d747.
Uwe Bugla reports that he cannot mount a floppy drive any more, and Jiri
Slaby bisected it down to this commit.
Benjamin LaHaise also points out that this is a big hot-path, and that
interrupt delivery while idle is very common and should not go through
all these expensive gyrations.
Fix up conflicts in arch/i386/kernel/apic.c and arch/i386/kernel/irq.c
due to other unrelated irq changes.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Uwe Bugla <uwe.bugla@gmx.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
aware
Since TEXT_OFFSET is meant to determine RAM location for kernel use,
itshould affect .data and .bss initial mapping in the XIP case.
Otherwise a XIP kernel would crash if TEXT_OFFSET gets somewhat larger
than 2MB.
Corresponding code is also moved up a bit to be near the similar .text
mapping code making the whole a bit more straight forward to understand.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 2552fc27ff XIP kernels failed
to boot because (_end - PAGE_OFFSET - 1) is much smaller than the size
of the kernel text and data in the XIP case, causing the kernel not to
be entirely mapped.
Even in the non-XIP case, the use of (_end - PAGE_OFFSET - 1) is wrong
because it produces a too large value if TEXT_OFFSET is larger than 1MB.
Finally the original code was performing one loop too many.
Let's break the loop when the section pointer has passed the last byte
of the kernel instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SN code to initialize the Hub/TIO infrastructure needs to
execute before bus scanning. This was previously done with
an early call to acpi_bus_register_driver(). But now that
ACPI is using the Linux driver model, a driver cannot be registered
that early. Make changes to have the init routines invoked via
calls to acpi_get_devices().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The new gpio_direction_input() and gpio_direction_output() functions
were both enabling output mode. When configuring a GPIO for input mode,
you need to program the ODR (Output Disable Register).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The duplicate file "include/asm-arm/arch-at91rm9200/entry-macro.S" can
be removed - it was already moved to include/asm-arm/arch-at91/.
Fix 3 small typo's - two in comments, and the incorrect clock was
specified for the LCD device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the Armzone QT2410 to the list of built
machines in the s3c2410_defconfig
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds trivial support for SMARTMIPS extension. This extension
is currently implemented by 4KS[CD] CPUs.
Basically it saves/restores ACX register, which is part of the SMARTMIPS
ASE, when needed. This patch does *not* add any support for Smartmips MMU
features.
Futhermore this patch does not add explicit support for 4KS[CD] CPUs since
they are respectively mips32 and mips32r2 compliant. So with the current
processor configuration, a platform that has such CPUs needs to select
both configs:
CPU_HAS_SMARTMIPS
SYS_HAS_CPU_MIPS32_R[12]
This is due to the processor configuration which is mixing up all the
architecture variants and the processor types.
The drawback of this, is that we currently pass '-march=mips32' option to
gcc when building a kernel instead of '-march=4ksc' for 4KSC case. This
can lead to a kernel image a little bit bigger than required.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since $(ARCH) is always "s390" we can replace it with "s390".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_SHARED_KERNEL the kernel text segment that might be in a
read only memory sections starts at 1MB. Memory between 0x12000 and
0x100000 is unused then. Free this, so we have appr. an extra MB
of memory available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Clear only memory from __bss_start to __bss_stop when clearing the bss
section. Not until _end, which currently happens to be the same.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To avoid ugly warings for older gccs, we replace
BUG() with "return NULL", which is just as well.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setup.h has been misused for ipl related stuff in the past. We now move
everything, which has to do with ipl and reipl to a new header file named
"ipl.h".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace two stidp inline assemblies with one global implementation.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Force reading of *in_sync in while loop. Loops where the content that
is checked for is changed by a different cpu always should have some
sort of barrier() semantics.
Otherwise this might lead to very subtle bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disable ZONE_DMA on 31-bit. All memory is addressable by all
devices and we do not need any special memory pool.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce __smp_call_function_map which calls a function on all cpus
given with a cpumask_t. Use it to implement smp_call_function and
smp_call_function_on. Replace smp_ext_bitcall_others with smp_ext_bitcall
and a for_each_cpu_mask loop. Use a cpumask_t instead of an atomic_t for
cpu counting and print a warning if preempt is on in
__smp_call_function_map().
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The new delay implementation uses the clock comparator and an external
interrupt even if it is called disabled for interrupts. To do this
all external interrupt source except clock comparator are switched of
before enabling external interrupts. The external interrupt at the
end of the delay period may not execute softirqs or we can end up in a
dead-lock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/241),
this patch
- adds gpio_direction_input/output functions to
generic.c instead of making them inline,
- fixes comment and includes and uses inline functions
instead of macros in gpio.h
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/242),
this patch:
- moves the PXA_LAST_GPIO check into pxa_gpio_mode
- fixes comment and includes in gpio.h
- replaces the gpio_set/get_value macros with inline
functions and adds a non-inline version to avoid
code explosion when gpio is not a constant.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was OpenVZ specific bug rendering some cpufreq drivers unusable on SMP.
In short, when cpufreq code thinks it confined itself to needed cpu by means
of set_cpus_allowed() to execute rdmsr, some "virtual cpu" feature can migrate
process to anywhere. This triggers bugons and does wrong things in general.
This got fixed by introducing rdmsr_on_cpu and wrmsr_on_cpu executing rdmsr
and wrmsr on given physical cpu by means of smp_call_function_single().
Dave Jones mentioned cpufreq might be not only user of rdmsr_on_cpu() and
wrmsr_on_cpu(), so I'm putting them into arch/{i386,x86_64}/lib/ .
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[NET] Eliminate user-selectable CONFIG_MV643XX_ETH_[012]
[MIPS] Drop __init from init_8259A()
[MIPS] Fix Kconfig typo bug
[MIPS] Fix double signal on trap and break instruction
[MIPS] sigset_32 has been made redundand by compat_sigset_t.
[MIPS] emma2rh: Remove needless <asm/i8259.h> inclusion.
[MIPS] Add MTD device support for Cobalt
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>
init_8259A() is called from i8259A_resume() so should not be marked as
__init. And add some tests for whether 8259A was already initialized
or not.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This commit broke gdb, since any BREAK or TRAP instruction cause SIGSEGV.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has added MTD device support for Cobalt.
Moreover, removes old type FlashROM support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On S3C24XX architecture, select CONFIG_NO_IOPORT
as we only have memory based IO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
kernel/built-in.o: In function `pm_suspend':
utsname_sysctl.c:(.text+0x23008): multiple definition of `pm_suspend'
arch/arm/mach-sa1100/built-in.o:arch/arm/mach-sa1100/sleep.S:(.text+0xf68): first defined here
arm-linux-ld: Warning: size of symbol `pm_suspend' changed from 20 in arch/arm/mach-sa1100/built-in.o to 44 in kernel/built-in.o
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CC arch/arm/mach-iop13xx/setup.o
arch/arm/mach-iop13xx/setup.c: In function 'iq8134x_probe_flash_size':
arch/arm/mach-iop13xx/setup.c:210: warning: implicit declaration of function 'ioremap'
arch/arm/mach-iop13xx/setup.c:210: warning: initialization makes pointer from integer without a cast
arch/arm/mach-iop13xx/setup.c:218: warning: implicit declaration of function 'writew'
arch/arm/mach-iop13xx/setup.c:222: warning: implicit declaration of function 'readb'
arch/arm/mach-iop13xx/setup.c:231: warning: implicit declaration of function 'iounmap'
LD .tmp_vmlinux1
arch/arm/mach-iop13xx/built-in.o: In function `iop13xx_platform_init':
iq81340mc.c:(.init.text+0x150): undefined reference to `ioremap'
iq81340mc.c:(.init.text+0x21c): undefined reference to `writew'
iq81340mc.c:(.init.text+0x24c): undefined reference to `writew'
iq81340mc.c:(.init.text+0x254): undefined reference to `iounmap'
iq81340mc.c:(.init.text+0x2c4): undefined reference to `readb'
iq81340mc.c:(.init.text+0x2e8): undefined reference to `readb'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CC arch/arm/common/sharpsl_pm.o
arch/arm/common/sharpsl_pm.c:30:31: error: asm/apm-emulation.h: No such file or directory
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Per device data such as brightness belongs to the indivdual device
and should therefore be separate from the the backlight operation
function pointers. This patch splits the two types of data and
allows simplifcation of some code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
backlight_device->sem has a very specific use as documented in the
header file. The external users of this are using it for a different
reason, to serialise access to the update_status() method.
backlight users were supposed to implement their own internal
serialisation of update_status() if needed but everyone is doing
things differently and incorrectly. Therefore add a global mutex to
take care of serialisation for everyone, once and for all.
Locking for get_brightness remains optional since most users don't
need it.
Also update the lcd class in a similar way.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
From the 01408c4939 log message:
The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source
address is not immediately available the copy fails *and* *zeros* *the*
*destination*.
This is a problem because a concurrent read (which admittedly is an odd
thing to do) might see zeros rather that was there before the write, or
what was there after, or some mixture of the two (any of these being a
reasonable thing to see).
If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't
cause an error.
The first copying does not need to zero any uncopied bytes, and doing
so causes the problem. It uses copy_from_user_atomic rather than
copy_from_user so the simple expedient is to change copy_from_user_atomic
to *not* zero out bytes on failure.
< --- end cite --- >
This patch finally implements at least a not so pretty solution by
duplicating the relevant part of __copy_user.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes some sparse warnings. ("warning: symbol 'foo' was not
declared. Should it be static?")
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The broadcast functionality is only necessary when a local APIC is
available. Make the config switch depend on X86_LOCAL_APIC. This
resolves the mach-voyager breakage introduced by the tick managament
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powerpc gets:
init/main.c: In function `do_basic_setup':
init/main.c:714: warning: implicit declaration of function `init_irq_proc'
but we cannot include linux/irq.h in generic code.
Fix it by moving the declaration into linux/interrupt.h instead.
And make sure all code that defines init_irq_proc() is including
linux/interrupt.h.
And nuke an ifdef-in-C
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Update defconfigs
[MIPS] Support for several more SNI RM models.
[MIPS] Include <asm/bugs> to for declaration of check_bugs32.
[MIPS] Add external declaration of pagetable_init() to pgalloc.h
[MIPS] Make kernel_thread_helper() static
[MIPS] Make __declare_dbe_table static and avoid it getting optimized away
[MIPS] Use MIPS R2 instructions for bitops.
[MIPS] signals: Share even more code.
[MIPS] Fix CONFIG_MIPS32_N32=y CONFIG_MIPS32_O32=n build
[MIPS] Iomap implementation.
[MIPS] <asm/compat-signal.h> needs to include <asm/uaccess.h>.
[MIPS] IP27: Fix warning.
[MIPS] Fix sigset_t endianess swapping issues in 32-bit compat code.
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (34 commits)
[POWERPC] 86xx: Cleaned up platform dts files
[POWERPC] 85xx: Renamed MPC8568 MDS board code to match other boards
[POWERPC] 85xx: Cleaning up machine probing
[POWERPC] QE: clean up ucc_slow.c and ucc_fast.c
[POWERPC] 85xx: Cleaned up platform dts files
[POWERPC] 83xx: Renamed MPC8323 MDS dts and defconfig to match other boards
[POWERPC] 83xx: Updated and renamed MPC8360PB to MPC836x MDS
[POWERPC] 83xx: Use of_platform_bus_probe to setup QE devices
[POWERPC] 83xx: use default value of loops_per_jiffy
[POWERPC] 83xx: Remove obsolete setting of ROOT_DEV.
[POWERPC] 83xx: Cleaning up machine probing and board initcalls
[POWERPC] Dispose irq mapping when done in mpc52xx_serial.c
[POWERPC] 86xx: Add missing of_node_put() in mpc86xx_hpcn_init_irq().
[POWERPC] 8[56]xx: Remove obsolete setting of ROOT_DEV for 85xx and 86xx platforms.
[POWERPC] pseries: Enabling auto poweron after power is restored.
[POWERPC] use winbond libata instead of ide driver for pseries CD drives
[POWERPC] powerpc: remove references to the obsolete linux,platform property
[POWERPC] add of_get_mac_address and update fsl_soc.c to use it
[POWERPC] 83xx: Cleaned up 83xx platform dts files
[POWERPC] Fix bug with early ioremap and 64k pages
...
This fixes some sparse warnings.
pgtable-32.c:15:6: warning: symbol 'pgd_init' was not declared. Should it be static?
pgtable-32.c:32:13: warning: symbol 'pagetable_init' was not declared. Should it be static?
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This implementation has support for the concept of one separate ioport
address space by PCI domain. A pointer to the virtual address where
the port space of a domain has been mapped has been added to struct
pci_controller and systems should be fixed to fill in this value. For
single domain systems this will be the same value as passed to
set_io_port_base().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
access_ok in compat-signal.h is wrong (checking destination instead of
source) and redundant (already checked before calling this function).
Also sf_mask in struct sigframe32 should be compat_sigset_t type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Removed explicit linux,phandle usage. Use references and labels now
* Removed interrupts property from openpic node
* Removed interrupt-parent property from openpic node that pointed to itself
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
On the n2100, both onboard r8169 ports exhibit PCI parity problems.
Set the ->broken_parity_status flag for both ports so that the r8169
drivers knows it should ignore error interrupts.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Renamed the MPC8568 MDS platform code to follow other 85xx boards. There
isn't anything specific about the 8568 MDS code that wouldn't apply to another
85xx MDS system at this point.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up the probing functionality to be more consistent across all 85xx
boards and actually check to see if we should be running on a given board.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactored and cleaned up ucc_fast.c and ucc_slow.c so that the two files
look more alike and are easier to read. Removed uccf_printk() and related
functions, because they were just front-ends to printk(). Fixed some
spacing and tabbing issues. Minor optimizations of some code. Changed
the type of some variables to their proper type (mostly buffer
descriptors).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fixed up top level compatible property for all boards
* Removed explicit linux,phandle usage. Use references and labels now
* Fixed phy-phandles for TSEC3/4 in mpc8548cds.dts
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a follow up for the patch providing the base support for the
ns9xxx machine type.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2443_PM is not defined in our Kconfig, so
remove the reference from CPU_S3C2443 to stop
the configuration process warning about it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix "spin_lock_irqrestore" to "spin_unlock_irqrestore."
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Change the explicit code in the relocs.c file to use ARRAY_SIZE()
and add a definition of ARRAY_SIZE() since this is a userspace program
and wouldn't include kernel.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Replace the very few remaining "depends" Kconfig directives with
"depends on".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Renamed the MPC8323 MDS and defconfig to match the naming convention followed
by other MDS boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC836x PB board is really just one part of the MPC836x MDS. We currently
name all other PB boards as MDS. Removed all references to PB and replaced
with MDS. Additionally renamed the .dts to match the defconfig (mpc836x_mds*).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use of_platform_bus_probe to setup devices on the of_platform_bus since its
much cleaner. We explicitly specify the bus ids since the we want to get rid
of the default mechanism in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the default value setup by initialization of loops_per_jiffy, its close
enough for 83xx and will get fixed up by calibrate_delay().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up the probing functionality to be more consistent across all 83xx
boards and added machine_is() protection around board initcalls to ensure they
only do something if we are actually running on that board.
Additionally, removed some dead code on mpc832x_mds.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* architecture specific details are handled in asm/arch/time.h
* ARCH_IOP13XX now selects PLAT_IOP
* as suggested by Lennert use ifdef CONFIG_XSCALE to skip the cp_wait on
XSC3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This functionality is replaced by cp6_trap
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_irqnr_preamble allows machines to take some action before entering the
get_irqnr_and_base loop. On iop we enable cp6 access.
arch_ret_to_user is added to the userspace return path to allow individual
architectures to take actions, like disabling coprocessor access, before
the final return to userspace.
Per Nicolas Pitre's note, there is no need to cp_wait on the return to user
as the latency to return is sufficient.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add initialisation and mappings for S3C2443 DMA
system
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch gets the DMA system for the S3C24XX
ready for the S3C2443, which requires 6 dma channels
at a different stride, and different base IRQ.
The DMA system is now initialised from the same
drivers which apply the DMA mappings, as well
as removing the DMA sysdev intialisation out of
the main init code (which is now being called
from a sysdev probe, so cannot add a new sysdev)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the Kconfig of arch/arm/mach-s3c2443 to
add the CONFIG_CPU_S3C2443 to the list of config
variabls which mean CONFIG_CPU_S3C2412_ONLY cannot
be set
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the DMA code's channel printing at startup
as this is firstly a waste of console output on
initialsaion, and secondly is going to be obsolete
once the S3C2443 DMA code has been merged
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from: Harald Welte <laforge@openmoko.org>
Add support for the Armzone QT2410 system, with
basic peripheral support for TFT display, SPI
and LEDs.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Ben Dooks <ben-linux@fluf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In copy_siginfo_from_user32:
Use compat_uptr_t. Use compat_ptr().
In copy_siginfo_to_user32:
Use compat_int_t. Use ptr_to_compat().
The sigevent_t structure has a 64-bit si_ptr field
that when copied to a 32-bit si_ptr will copy the wrong
word. For the compat copy use the si_int field instead.
Signed-off-by: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Move migrate_pages into the same position as specified
in unistd.h. This fixes migrate_pages, pselect6 and
ppoll syscalls.
Signed-off-by: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
- this macro unifies the code to add exception table entries
- additionally use ENTRY()/ENDPROC() at more places
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
And remove it's reference in time.c.
Allow lcd_print() to take a const char *.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
show_stack() was calling kzalloc() to allocate a struct pt_regs.
This meant that *really* early stack dumps would cause a null pointer
dereference. x86_64 allocates its pt_regs on the stack, so do the same.
Kyle actually committed this exact patch to CVS on
Wed Jul 26 14:32:39 2006 UTC, and never moved it across to git.
Bad Kyle.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Al Viro did this for x86-64 and reduced the number of dependencies on
sched.h significantly. We had a couple of files which were relying on
uaccess.h pulling in sched.h, so they need explicit dependencies added.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
acpi_boot_init() is making a bad check on the return
status from acpi_table_parse(). acpi_table_parse() now
returns zero on success, one on failure.
Signed-off-by: Aaron Young <ayoung@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is an additional list of systems that exhibit the PCI device ordering
issue that prompted the following patch:
commit 6b4b78fed4
Author: Matt Domsch <Matt_Domsch@dell.com>
Date: Fri Sep 29 15:23:23 2006 -0500
PCI: optionally sort device lists breadth-first
Adding these systems to the list prevents the need for the additional
kernel command line argument.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During power outages, the UPS notifies the system for a shutdown.
In the current setup, it isn't possible to poweron when power is
restored. This patch fixes the issue by calling the right
ibm,power-off-ups token during such events. It also adds a sysfs
interface so userspace can specify whether or not to power on when
power is restored.
Signed-off-by: Manish Ahuja <ahuja@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the default for the built-in IDE on p610/p615/p630 from
ide to libata. libata has better error handling and the drive can
recover when hald does its CD media polling.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add function of_get_mac_address(), which obtains the best MAC address to use
from the device tree by checking various properties in order. The order is:
'mac-address', then 'local-mac-address', then 'address'. It skips properties
that contain invalid MAC addresses, which were probably not initialized
by U-Boot.
Update gfar_of_init() and fs_enet_of_init() in fsl_soc.c to call
of_get_mac_address().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix build glitches on ARM ... the only user of "rtc_lock" today is the
optional PC-style "CMOS" RTC driver, the legacy SA1100 RTC driver is
not even in the tree any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Use per-controller spi_board_info structures
[AVR32] Warn, don't BUG if clk_disable is called too many times
[AVR32] Make sure all genclocks have a parent
[AVR32] Remove unnecessary sys_nfsservctl conditional
[AVR32] Wire up the SysV IPC calls properly
[AVR32] Define ioremap_nocache, ioport_map and ioport_unmap
[AVR32] Fix prototypes for __raw_writesb and friends
Now that disable_irq() defaults to delayed-disable semantics, the IRQ_DISABLED
flag is not needed anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Never mask interrupts immediately upon request. Disabling interrupts in
high-performance codepaths is rare, and on the other hand this change could
recover lost edges (or even other types of lost interrupts) by conservatively
only masking interrupts after they happen. (NOTE: with this change the
highlevel irq-disable code still soft-disables this IRQ line - and if such an
interrupt happens then the IRQ flow handler keeps the IRQ masked.)
Mark i8529A controllers as 'never loses an edge'.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts x86_64 to use the GENERIC_TIME infrastructure and adds
clocksource structures for both TSC and HPET (ACPI PM is shared w/ i386).
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: fix printk ckeanups]
[akpm@osdl.org: hpet build fix]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for the x86_64 generic time conversion, this patch splits out
TSC and HPET related code from arch/x86_64/kernel/time.c into respective
hpet.c and tsc.c files.
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for supporting generic timekeeping, this patch cleans up
x86-64's use of vxtime.hpet_address, changing it to just hpet_address as is
also used in i386. This is necessary since the vxtime structure will be going
away.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NMI watchdog implementation assumes that the local APIC timer interrupt is
happening. This assumption is not longer true when high resolution timers and
dynamic ticks come into play, as they may switch off the local APIC timer
completely. Take the PIT/HPET interrupts into account too, to avoid false
positives.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local apic timer calibration has two problem cases:
1. The calibration is based on readout of the PIT/HPET timer to detect the
wrap of the periodic tick. It happens that a box gets stuck in the
calibration loop due to a PIT with a broken readout function.
2. CoreDuo boxen show a sporadic PIT runs too slow defect, which results
in a wrong lapic calibration. The PIT goes back to normal operation once
the lapic timer is switched to periodic mode.
Both are existing and unfixed problems in the current upstream kernel and
prevent certain laptops and other systems from booting Linux.
Rework the code to address both problems:
- Make the calibration interrupt driven. This removes the wait_timer_tick
magic hackery from lapic.c and time_hpet.c. The clockevents framework
allows easy substitution of the global tick event handler for the
calibration. This is more accurate than monitoring jiffies. At this point
of the boot process, nothing disturbes the interrupt delivery, so the
results are very accurate.
- Verify the calibration against the PM timer, when available by using the
early access function. When the measured calibration period is outside of
an one percent window, then the lapic timer calibration is adjusted to the
pm timer result.
- Verify the calibration by running the lapic timer with the calibration
handler. Disable lapic timer in case of deviation.
This also removes the "synchronization" of the local apic timer to the global
tick. This synchronization never worked, as there is no way to synchronize
PIT(HPET) and local APIC timer. The synchronization by waiting for the tick
just alignes the local APIC timer for the first events, but later the events
drift away due to the different clocks. Removing the "sync" is just
randomizing the asynchronous behaviour at setup time.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clockevent drivers for i386: lapic (local) and PIT/HPET (global). Update
the timer IRQ to call into the PIT/HPET driver's event handler and the
lapic-timer IRQ to call into the lapic clockevent driver. The assignement of
timer functionality is delegated to the core framework code and replaces the
compile and runtime evalution in do_timer_interrupt_hook()
Use the clockevents broadcast support and implement the lapic_broadcast
function for ACPI.
No changes to existing functionality.
[ kdump fix from Vivek Goyal <vgoyal@in.ibm.com> ]
[ fixes based on review feedback from Arjan van de Ven <arjan@infradead.org> ]
Cleanups-from: Adrian Bunk <bunk@stusta.de>
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The apic code is quite unstructured and missing a lot of comments.
- Restructure the code into helper functions, timer, setup/shutdown,
interrupt and power management blocks.
- Fixup comments.
- Namespace fixups
- Inline helpers for version and is_integrated
- Combine the ack_bad_irq functions
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow early access to the power management timer by exposing the verified read
function and providing a helper function which checks the pmtmr_ioport
variable and returns either the pm timer readout or 0 in case the pm timer is
not available.
Create a new header file and replace also the ifdef'ed extern definition in
arch/i386/kernel/acpi/boot.c
This is a preperatory patch for the rework of the local apic timer
calibration.
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Geode can safely use the TSC for highres, since:
1) Does not support frequency scaling,
2) The TSC _does_ count when the CPU is halted. Furthermore, the Geode
supports a mode called "suspension on halt", where Suspend mode (which
interacts with the power management states) is entered. TSC counting
during suspend mode is controlled by bit 8 of the Bus Controller
Configuration Register #0 (thanks Tom!).
3) no SMP :)
Check if "RTSC counts during suspension" and remove the requirement for
verification, so the clocksource code can safely select it as an timesource
for the highres timers subsystem.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSC needs to be verified against another clocksource. Instead of using
hardwired assumptions of available hardware, provide a generic verification
mechanism. The verification uses the best available clocksource and handles
the usability for high resolution timers / dynticks of the clocksource which
needs to be verified.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clocksource code allows direct updates of the rating of a given
clocksource now. Change TSC unstable tracking to use this interface and
remove the update callback.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.
[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make the TSC synchronization code more robust, and unify it between x86_64 and
i386.
The biggest change is the removal of the 'fix up TSCs' code on x86_64 and
i386, in some rare cases it was /causing/ time-warps on SMP systems.
The new code only checks for TSC asynchronity - and if it can prove a
time-warp (if it can observe the TSC going backwards when going from one CPU
to another within a critical section), then the TSC clock-source is turned
off.
The TSC synchronization-checking code also got moved into a separate file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enqueue clocksources in rating order to make selection of the clocksource
easier. Also check the match with an user override at enqueue time.
Preparatory patch for the generic clocksource verification.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The delayed work code in arch/i386/kernel/tsc.c is an unused leftover of the
GTOD conversion. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag so we can prevent the irq balancing of an interrupt. Move the
bits, so we have room for more :)
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/i386/kernel/built-in.o: In function `vmi_stop_hz_timer':
: undefined reference to `next_timer_interrupt'
If CONFIG_NO_HZ, next_timer_interrupt() doesn't exist (and presumably doesn't
make sense).
Perhaps VMI shouildn't be playing with timer internals at this level.
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A previous cleanup misused need_poll, which had a fairly broken interface.
It implemented a growable array, changing the used elements count itself,
but leaving it up to the caller to fill in the actual elements, including
the entire array if the array had to be reallocated. This worked because
the previous users were switching between two such structures, and the
elements were copied from the inactive array to the active array after
making sure the active array had enough room.
maybe_sigio_broken was made to use need_poll, but it was operating on a
single array, so when the buffer was reallocated, the previous contents
were lost.
This patch makes need_poll implement more sane semantics. It merely
assures that the array is of the proper size and that the contents are
preserved. It is up to the caller to adjust the used elements count and to
ensure that the proper elements are resent.
This manifested itself as a hang in 2.6.20 as the uninitialized buffer
convinced UML that one of its own file descriptors didn't support SIGIO and
needed to be watched by poll in a separate thread. The result was an
interrupt flood as control traffic over this descriptor sparked interrupts,
which resulted in more control traffic, ad nauseum.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Fixed up top level compatible property for all boards
* Removed explicit linux,phandle usage. Use references and labels now
* Fixed interrupt sense attribute, some interrupts were marked edge, that are level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add kexec support to ARM.
Improvements like commandline handling could be made but this patch gives
basic functional support. It uses the next available syscall number, 347.
Once the syscall number is known, userspace support will be
finalised/submitted to kexec-tools, various patches already exist.
Originally based on a patch by Maxim Syrchin but updated and forward
ported by various people.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In some situations, the pen_release store in platform_secondary_init()
may stay forever in the write buffer while the CPU is waiting on the
boot_lock to be released in boot_secondary(). The primary CPU could
never see the pen_release update without the barriers.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Remove a duplicated define for AT91_RSTC_KEY
- Set AT91_RSTC_KEY to the correct value
- Replace the hardcoded keys in at91sam9620.c and at91sam9261.c
by AT91_RSTC_KEY
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When "rtc-at91" was renamed to "rtc-at91rm9200" not all the relevant
defconfig entries were updated.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set up one spi_board_info array per controller and pass this to
at32_add_device_spi so that it can set up any GPIO pins for chip
selects based on this information.
Extracted from a patch by David Brownell and adapted slightly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Commit 1c9d3df5e8 added function prototype
__flush_dcache_page() in include/asm-arm/cacheflush.h. So we can remove
the prototype for same in arch/arm/mm/fault-armv.c since it is now
redundant to have it there.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Print a helpful warning along with a stack dump if clk_disable is
called on a already-disabled clock. Remove the BUG_ON().
Extracted from a patch by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Initialize the parent field of each generic clock by looking at the
PM registers. This means that the genclock operations can always
assume that the parent field is non-null, so they don't have to
check. Also remove a few unnecessary BUG_ON()s.
Extracted from a patch by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add IRQ handlers for the IRQs which originate
from the sub-interrupt register on the S3C2443
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Machines in the S3C24XX architectures should not
be including <asm/hardware/iomd.h> as this is not
needed.
Also remove commented out includes
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
kernel/sys_ni.c defines sys_nfsservctl as a weak alias for
sys_ni_syscall, so it's always safe to include it in the system
call table.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Wire up the individual sysvipc system calls and remove sys_ipc.
Strictly speaking, this breaks the ABI, but since sys_ipc never
worked anyway due to a silly bug, it isn't actually a regression.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Set the LCD display type field in the platform data
so that the LCD driver initialise the display as an
TFT display
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook in a cpu specific reset function for the S3C2443
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the S3C2412 nand driver for the S3C2443 as it
is register compatible.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for SMDK2443 to arch/arm/mach-s3c2443
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add arch/arm/mach-s3c2443 for support of the Samsung S3C2443 SoC
This patch adds the core CPU support, clock framework, times
and initial IRQ support, as well as adding the directory into
the build tree.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code for bolting hash entries for ioremap done before proper
mm initialization has a grown a bug when using 64K pages on a
machine where non-cacheable mappings are demoted to 4K HW pages.
The wrong page size index is being passed to the hash table mapping
functions causing a crash at boot on some pSeries machines using
bare metal linux. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My "cleanup" patch (dce623e082) had a cut
and paste error for the !CONFIG_KEXEC case. Fifty lashes for me.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without this, building drivers/serial/of_serial.c as a module fails.
WARNING: ".of_find_property" [drivers/serial/of_serial.ko] undefined!
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'linux,boot-cpu' property is obsolete, so remove it from all of the DTS
files and from booting-without-of.txt. The boot CPU is actually defined in
the device tree header, and U-Boot sets that field. The device tree compiler
also complains if the property exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scc_uhc.c depends on CONFIG_PCI, not CONFIG_USB. Because CONFIG_PCI
is always "y" on Celleb platform, we move scc_uhc.o to obj-y.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the MPIC IPIs to be per-CPU to avoid getting a
warning ("Cannot set affinity for irq 251") when taking a CPU
offline via sysfs or during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds driver code for the PMI device found in future IBM products.
PMI stands for "Platform Management Interrupt" and is a way to
communicate with the BMC (Baseboard Management Controller).
It provides bidirectional communication with a low latency.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 system manager support and the ppc_md routines restart() and
power_off().
The system manager provides an event notification mechanism for reporting
events like thermal alert and button presses. It also provides support to
control system shutdown and startup.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an ATA drive uses legacy mode, ata driver will choose 14 and 15
as the fixed irq number. On ia64 platform, such numbers are GSI and
should be converted to irq vector.
Below patch against kernel 2.6.20 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the Atmel AT91SAM9XE range of processors. These are
basically AT91SAM9260's with different amounts of internal SRAM and
Flash.
We make use of the existing AT91SAM9260 support, but just perform
run-time detection of the size of the internal SRAM.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the L220 on the RealView/EB MPCore platform.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kernel originally supported revB only. This patch enables revC by
default and adds a config option for building the kernel for the revB
platform. Since the SCU base address was hard-coded in the proc-v6.S
file (and only valid for RealView/EB revB), this patch also adds a
more generic support for defining the SCU information.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MPCore platform
This patch adds the registration of the secondary GIC on the
baseboard, together with the IRQ chaining setup.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation only assumes one GIC to be present in the
system. However, there are platforms with more than one cascaded interrupt
controllers (RealView/EB MPCore for example).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Start using v2 version of Longhaul when available. It provides
voltage scaling and can use ACPI C3 state. That's curious. CPU
will not change frequency on ACPI C3 when v1 is in use, but it will
when v2 is used. Driver will return max frequency all the time if
this isn't true for all processors. There is strange thing with
mobile voltage. Looks like only Nehemiah (C3-M) supports it.
Earlier processors have different mobile VRM (in docs), but I can't
find any which is using it. Looks like all are using VRM 8.5. So
fail for non Nehemiah with mobile VRM.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basically everything was done but I removed all element initializers from the
trailing entries to make it clear the entire last entry should be zero filled.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only sysctl x86_64 provides are not provided elsewhere, so insert_at_head
is unnecessary.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While doing the C99 conversion I notices that the top level sh64 directory was
using the binary number for CTL_KERN. That is a no-no so I removed the
support for the sysctl binary interface only leaving sysctl /proc support.
At least the sysctl tables were placed at the end of the list so user space
did not see this mistake.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And make the mode of the kernel directory 0555 no one is allowed to write to
sysctl directories.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was partially done already and there was no ABI breakage what a relief.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to have the the definition of all top level sysctl directories
registers in sysctl.h so we don't conflict by accident and cause abi problems.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While C99 converting the ctl_table initializers I realized that the binary
sysctl numbers were in conflict with the binary values under CTL_KERN.
Including CTL_KERN KERN_VERSION as used by glibc. So I just removed the
sysctl binary interface for these values, as it was unsupportable.
Luckily these sysctl were inserted at the end of the sysctl list so this bug
was not visible to userspace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The assignment of binary numbers for sys_sysctl use was in shambles and
despite requiring methods. Nothing was implemented on the sys_sysctl side.
So this patch gives a mercy killing to the sys_sysctl support for
powermanagment on mips/au1000.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This convters the sysctl ctl_tables to use C99 initializers. While I was
looking at it I discovered it was using a portion of the sysctl binary
addresses space under CTL_KERN KERN_OSTYPE which was completely inappropriate.
So I completely removed all of the sysctl binary names, to remove and avoid
the ABI conflict.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By not using the enumeration in sysctl.h (or even understanding it) the SN
platform placed their arch specific xpc directory on top of CTL_KERN and only
because they didn't have 4 entries in their xpc directory got lucky and didn't
break glibc.
This is totally irresponsible. So this patch entirely removes sys_sysctl
support from their sysctl code. Hopefully they don't have ascii name
conflicts as well.
And now that they have no ABI numbers add them to the end instead of the
sysctl list instead of the head so nothing else will be overridden.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the binary sysctl numbers are unique putting the registered sysctls at
the head of the sysctl list where they can override existing sysctls serves no
useful purpose.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
