Commit Graph

291 Commits

Author SHA1 Message Date
Jeff Garzik
e6331173c8 Revert "[PATCH] e1000: disable TSO on the 82544 with slab debugging"
This reverts commit 72f3ab7462, which was
superceded by commit 683a2aa339
("e1000: Do not truncate TSO TCP header with 82544 workaround"), which
fixed the real problem.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-07 22:57:38 -05:00
Herbert Xu
683a2aa339 e1000: Do not truncate TSO TCP header with 82544 workaround
The e1000 driver has a workaround for 82544 on PCI-X where if the
terminating byte of a buffer is at addresses 0-3 mod 8, then 4 bytes
are shaved off it and defered to a new segment.  This is due to an
erratum that could otherwise cause TX hangs.

Unfortunately this breaks TSO because it may cause the TCP header to
be split over two segments which itself causes TX hangs.  The solution
is to pull 4 bytes of data up from the next segment rather than pushing
4 bytes off.  This ensures the TCP header remains in one piece and
works around the PCI-X hang.

This patch is based on one from Jesse Brandeburg.

This bug has been trigered by both CONFIG_DEBUG_SLAB as well as Xen.

Note that the only reason we don't see this normally is because the
TCP stack starts writing from the end, i.e., it writes the TCP header
first then slaps on the IP header, etc.  So the end of the TCP header
(skb->tail - 1 here) is always aligned correctly.

Had we made the start of the IP header (e.g., IPv6) 8-byte aligned
instead, this would happen for normal TCP traffic as well.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
--
Visit Openswan at http://www.openswan.org/
Email: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 16:28:20 -05:00
Jesse Brandeburg
79f3d3996f [PATCH] e1000: No-delay link detection at interface up
Currently after an interface up, the link state is detected 2 seconds later
when the first watchdog timer runs. This patch changes that by triggering
the hardware to generate a link-change interrupt from the up() function
instead. This has the result that the link state gets detected immediately
and without races. This has the potential to speed up booting since a normal
distribution boot process waits for a link before DHCP is attempted.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Jeff Garzik
15e376b4ee e1000: 3 new driver stats for managability testing
Add 3 extra packet redirect counters for tracking purposes to make sure
we can test that all packets arrive properly.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Jesse Brandeburg
1f753861d2 [PATCH] e1000: Make the copybreak value a module parameter
Allow the user to vary the size that copybreak works. Currently cb is enabled
for packets < 256 bytes, but various tests indicate that this should be
configurable for specific use cases. In addition, this parameter allows us
to force never/always during testing to get full and predictable coverage of
both code paths.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Bruce Allan
018ea44ef1 [PATCH] e1000: Fix PBA allocation calculations
Assign the PBA to be large enough to contain at least 2 jumbo frames on
all adapters. This dramatically increases performance on several adapters
and fixes TX performance degradation issues where the PBA was misallocated
in the old algorithm.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Jesse Brandeburg
d89b6c6750 [PATCH] e1000: narrow down the scope of the tipg timer tweak
the driver has (ancient) code for messing with TIPG from the 82542 days.
Unfortunately this code was running on our current adapters and setting
TIPG for fiber to be +1 over the copper value.  This caused 1.45Mpps
to be sent instead of 1.487Mpps.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Jeff Kirsher
c3813ae661 [PATCH] e1000: fix ethtool reported bus type for older adapters
For older adapters we know that they are of the PCI bus type, so we can
just set this.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Bruce Allan
83cd827977 [PATCH] e1000: fix to set the new max frame size before resetting the adapter
This bugfix makes sure that the driver data reflects the full new situation
before the adapter is reinitialized.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Jeff Garzik
bb8e3311ef e1000: workaround for the ESB2 NIC RX unit issue
In rare occasions, ESB2 systems would end up started without the RX
unit being turned on. Add a check that runs post-init to work around
this issue.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:30 -05:00
Jesse Brandeburg
72f3ab7462 [PATCH] e1000: disable TSO on the 82544 with slab debugging
CONFIG_DEBUG_SLAB changes alignments of the data structures the slab
allocators return. These break certain workarounds for TSO on the 82544.
Since DEBUG_SLAB is relatively rare and not used for performance sensitive
cases, the simplest fix is to disable TSO in this special situation.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:29 -05:00
Jesse Brandeburg
3d5460a0ba [PATCH] e1000: Fix Wake-on-Lan with forced gigabit speed
If the user has forced gigabit speed, phy power management must be disabled;
otherwise the NIC would try to negotiate to a linkspeed of 10/100 mbit on
shutdown, which would lead to a total loss of link. This loss of link breaks
Wake-on-Lan and IPMI.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:29 -05:00
Jeff Garzik
0fccd0e9e3 e1000: consolidate managability enabling/disabling
Several bugs existed in how we handle manageability issues all
over the driver.  This patch consolidates all the managability
release and init code in two single functions and call them from
appropriate locations. This fixes several BMC packet redirect issues
and powerup/down hiccups.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:29 -05:00
Jeff Garzik
167fb28416 e1000: omit stats for broken counter in 82543
The 82543 chip does not count tx_carrier_errors properly in FD mode;
report zeros instead of garbage.

Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:28 -05:00
Jeff Garzik
bd2371ebcc e1000: For sanity, reformat e1000_set_mac_type(), struct e1000_hw[_stats]
Makes future changes a bit more readable.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:28 -05:00
Jesse Brandeburg
2b65326e67 [PATCH] e1000: dynamic itr: take TSO and jumbo into account
The dynamic interrupt rate control patches omitted proper counting
for jumbo's and TSO resulting in suboptimal interrupt mitigation strategies.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:28 -05:00
Jesse Brandeburg
7d16e65ba5 [PATCH] e1000: The user-supplied itr setting needs the lower 2 bits masked off
The lower 2 bits of a user-supplied itr setting (via ethtool) need to be
masked off: These lower two bits are used as control bits.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 15:51:28 -05:00
David Howells
4c1ac1b491 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/infiniband/core/iwcm.c
	drivers/net/chelsio/cxgb2.c
	drivers/net/wireless/bcm43xx/bcm43xx_main.c
	drivers/net/wireless/prism54/islpci_eth.c
	drivers/usb/core/hub.h
	drivers/usb/input/hid-core.c
	net/core/netpoll.c

Fix up merge failures with Linus's head and fix new compilation failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 14:37:56 +00:00
Al Viro
ff1dcadb1b [NET]: Split skb->csum
... into anonymous union of __wsum and __u32 (csum and csum_offset resp.)

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-12-02 21:27:18 -08:00
Andrew Morton
d0bb53e102 e1000 linkage fix
ia64:

 drivers/built-in.o(.text+0xd9a72): In function `e1000_xmit_frame':
 : undefined reference to `csum_ipv6_magic'

Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:12:03 -05:00
Auke Kok
25006ac61e e1000: increment version to 7.3.15-k2
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:01 -05:00
Jesse Brandeburg
835bb12983 e1000: add dynamic itr modes
Add a new dynamic itr algorithm, with 2 modes, and make it the default
operation mode. This greatly reduces latency and increases small packet
performance, at the "cost" of some CPU utilization. Bulk traffic
throughput is unaffected.

The driver can limit the amount of interrupts per second that the
adapter will generate for incoming packets. It does this by writing a
value to the adapter that is based on the maximum amount of interrupts
that the adapter will generate per second.

Setting InterruptThrottleRate to a value greater or equal to 100 will
program the adapter to send out a maximum of that many interrupts per
second, even if more packets have come in. This reduces interrupt
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.

The default behaviour of the driver previously assumed a static
InterruptThrottleRate value of 8000, providing a good fallback value
for all traffic types,but lacking in small packet performance and
latency. The hardware can handle many more small packets per second
however, and for this reason an adaptive interrupt moderation algorithm
was implemented.

Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in
which it dynamically adjusts the InterruptThrottleRate value based on
the traffic that it receives. After determining the type of incoming
traffic in the last timeframe, it will adjust the InterruptThrottleRate
to an appropriate value for that traffic.

The algorithm classifies the incoming traffic every interval into
classes.  Once the class is determined, the InterruptThrottleRate
value is adjusted to suit that traffic type the best. There are
three classes defined: "Bulk traffic", for large amounts of packets
of normal size; "Low latency", for small amounts of traffic and/or
a significant percentage of small packets; and "Lowest latency",
for almost completely small packets or minimal traffic.

In dynamic conservative mode, the InterruptThrottleRate value is
set to 4000 for traffic that falls in class "Bulk traffic". If
traffic falls in the "Low latency" or "Lowest latency" class, the
InterruptThrottleRate is increased stepwise to 20000. This default
mode is suitable for most applications.

For situations where low latency is vital such as cluster or
grid computing, the algorithm can reduce latency even more when
InterruptThrottleRate is set to mode 1. In this mode, which operates
the same as mode 3, the InterruptThrottleRate will be increased
stepwise to 70000 for traffic in class "Lowest latency".

Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:00 -05:00
Jesse Brandeburg
9ac9828442 e1000: add dynamic generic MSI interrupt routine
Add a generic MSI interrupt routine that is IO read-free, speeding up
MSI interrupt handling.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:00 -05:00
Auke Kok
04fedbfbc3 e1000: reorder e1000_param.c
This file needs some cleanups and reordering - logically order it
so that relevant defines and code are together with properly quoted
defaults.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:00 -05:00
Jesse Brandeburg
6a042dab19 e1000: Only set IDE for tx when we are using TIDV/TADV
Spec fix: don't set IDE unless we are actually setting the tx
int delay time.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
2006-12-02 00:12:00 -05:00
Jeff Kirsher
2df7d59f28 e1000: rename ICH8 flash macros
ICH8 will soon be followed by newer chipsets bearing the same acronym,
thus we remove the '8' and make it independent of the version number in
the platform name.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:00 -05:00
Jesse Brandeburg
fcfb122425 e1000: add queue restart counter
Add a netif_wake/start_queue counter to the ethtool statistics to indicated
to the user that their transmit ring could be too small for their workload.

Signed-off-by: Jesse brandeburg <jesse.brandeburg@intel.com>
Cc: Jamal Hadi <hadi@cyberus.ca>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:00 -05:00
Auke Kok
fc2307d00c e1000: New hardware support
Add support for a Low Profile quad-port PCI-E adapter and 2 variants
of the ICH8 systems' onboard NIC's.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:12:00 -05:00
Jesse Brandeburg
a9ebadd640 e1000: Remove unneeded and unwanted memsets
This memsetting was added in a paranoid rage debugging TX hangs, but
are no longer of importance. We can beef up the performance quite a
bit removing them. Make sure to fill in next_to_watch to allow this.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
2006-12-02 00:12:00 -05:00
Auke Kok
996695de21 e1000: simplify skb_put call.
Simplify two calls to skb_put by removing one call to it.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:11:59 -05:00
Jeff Kirsher
2bc35c1078 e1000: reorder pci-e infor struct
Order pci-e capability struct according to bus/pci bus width ordering
preserving the hard pci spec numbers.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2006-12-02 00:11:59 -05:00
Jeff Kirsher
070f6ffbb8 e1000: fix VR powerdown code
On ich systems during PHY power down to D3, the voltage regulators
were left on.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2006-12-02 00:11:59 -05:00
Jesse Brandeburg
2ce9047f5d e1000: add mmiowb() for IA64 to sync tail writes
IA64 SMP systems were seeing TX issues with multiple cpu's attempting
to write tail registers unordered. This mmiowb() fixes the issue.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
2006-12-02 00:11:59 -05:00
Auke Kok
21c4d5e078 e1000: Enble early receive (ERT) on 82573
Enable early receives on 82573 for jumbo frame performance. Jumbo's
are only supported on 82573L with ASPM disabled.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:11:59 -05:00
Auke Kok
87ca4e5b8d e1000: FIX: enable hw TSO for IPV6
Enable TSO for IPV6. All e1000 hardware supports it. This reduces CPU
utilizations by 50% when transmitting IPv6 frames.

Fix symbol naming enabling ipv6 TSO. Turn off TSO6 for 10/100.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:11:58 -05:00
Auke Kok
b00dae7cce e1000: Remove DISABLE_MULR debug code
Remove debugging code disabling MULR (multiple reads). It's not usable
for a wide audience and there are no known problems with MULR right
now.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:11:58 -05:00
Auke Kok
90fb51358a e1000: whitespace changes, comments, typos
Small whitespace changes, comment changes, typo fixes.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-12-02 00:11:58 -05:00
Matt LaPlante
0779bf2d2e Fix misc .c/.h comment typos
Fix various .c/.h typos in comments (no code changes).

Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-11-30 05:24:39 +01:00
David Howells
65f27f3844 WorkStruct: Pass the work_struct pointer instead of context data
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.

For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.

To make this work, an extra flag is introduced into the management side of the
work_struct.  This governs auto-release of the structure upon execution.

Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function.  This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated..  This is a
problem if the auxiliary data is taken away (as done by the last patch).

However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems.  But then the work function must itself release the
work_struct by calling work_release().

In most cases, automatic release is fine, so this is the default.  Special
initiators exist for the non-auto-release case (ending in _NAR).


Signed-Off-By: David Howells <dhowells@redhat.com>
2006-11-22 14:55:48 +00:00
Auke Kok
edd106fc8a [PATCH] e1000: Fix regression: garbled stats and irq allocation during swsusp
e1000: Fix suspend/resume powerup and irq allocation

From: Auke Kok <auke-jan.h.kok@intel.com>

After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.

Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-07 04:27:51 -05:00
Auke Kok
ff1e55b078 e1000: Increment version to 7.2.9-k4
Significant fixes -> increment driver version.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:46:09 -07:00
Jesse Brandeburg
d2a1e2131a e1000: FIX: move length adjustment due to crc stripping disabled.
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:46:06 -07:00
Jesse Brandeburg
032fe6e9e2 e1000: FIX: Don't limit descriptor size to 4kb for PCI-E adapters
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:46:04 -07:00
Jesse Brandeburg
e64d7d0209 e1000: FIX: Disable Packet Split for non jumbo frames
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.

Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:46:01 -07:00
Bruce Allan
225a5dbd68 e1000: FIX: fix wrong txdctl threshold bitmasks
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:45:58 -07:00
Auke Kok
dc1f71f6b3 e1000: FIX: 82542 doesn't support WoL
Exclude 82542 when setting up WoL. This card does not do WoL at all.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:45:55 -07:00
Jesse Brandeburg
4ccc12aeec e1000: FIX: don't poke at manageability registers for incompatible adapters
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-10-24 14:45:53 -07:00
Linas Vepstas
7347b03d25 [PATCH] e1000: Reset all functions after a PCI error
During the handling of the PCI error recovery sequence, the current e1000
driver erroneously blocks a device reset for any but the first PCI
function.  It shouldn't -- this is a cut-n-paste error from a different
driver (which tolerated only one hardware reset per hardware card).

Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-10-21 14:08:24 -04:00
David Howells
7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
Auke Kok
76ddb3fd96 e100, e1000, ixgb: increment version numbers
e100-3.5.17-k2
e1000-7.2.9-k2
ixgb-1.0.117-k2

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
2006-09-27 12:54:22 -07:00