Move the check for SMBUS_QUICK in i2c_probe() after the forced
addresses have been handled. This makes it possible for a driver to
leave the probed address lists empty, only providing forced addresses,
and get i2c_probe to work even if the bus doesn't support SMBUS_QUICK.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/i2c-core.c | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)
Using s8 instead of u8 to store temperature register values saves a
few instructions on sysfs file read. The very same was done for
several other drivers a while ago (lm63, lm83, lm90...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
Convert the w83l785ts driver to use dynamic sysfs callbacks. This is a
small driver so the benefit is thin, but still worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 36 ++++++++++++++++++------------------
1 file changed, 18 insertions(+), 18 deletions(-)
Clean up name string usage in 12 i2c bus drivers:
* Use the i2c_adapter name for requesting the I/O region rather than
redefining a new string.
* Do not initialize the i2c_adapter name to "unset".
This should save a few data bytes here and there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-ali1535.c | 6 +++---
drivers/i2c/busses/i2c-ali1563.c | 6 ++++--
drivers/i2c/busses/i2c-ali15x3.c | 5 +++--
drivers/i2c/busses/i2c-amd756.c | 5 ++---
drivers/i2c/busses/i2c-amd8111.c | 4 +++-
drivers/i2c/busses/i2c-i801.c | 4 ++--
drivers/i2c/busses/i2c-nforce2.c | 4 ++--
drivers/i2c/busses/i2c-piix4.c | 4 ++--
drivers/i2c/busses/i2c-sis5595.c | 5 +++--
drivers/i2c/busses/i2c-sis630.c | 6 ++++--
drivers/i2c/busses/i2c-sis96x.c | 5 +++--
drivers/i2c/busses/i2c-via.c | 4 ++--
12 files changed, 33 insertions(+), 25 deletions(-)
Discard a common out-of-date comment in 5 hardware monitoring drivers.
The hardware monitoring chip drivers are no more setting sensor limits
at initialization time, for quite some time already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/lm78.c | 1 -
drivers/hwmon/via686a.c | 1 -
drivers/hwmon/w83627hf.c | 1 -
drivers/hwmon/w83781d.c | 1 -
drivers/hwmon/w83792d.c | 1 -
5 files changed, 5 deletions(-)
Do not enable the VIA VT82C686A/B integrated sensors by default, as
disabled sensors usually means that this feature is not used so the
values won't make any sense. This has been confusing many users in the
past:
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1786http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1811http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=2052
It is still possible to forcibly enable the sensors by using the
force_addr module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/hwmon/via686a | 17 +++++++++++++++--
drivers/hwmon/via686a.c | 18 +++++++++++-------
2 files changed, 26 insertions(+), 9 deletions(-)
We can save 0.5kB of data in the via686a driver.
From: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 2/2: convert to use dynamic sysfs accessors
This patch converts adm9240 to use Yani Ioannou's dynamic sysfs callbacks,
reducing driver memory footprint from 16312 to 14104 bytes on 2.6.14-rc1,
removing the old driver macro mess.
Run tested on Intel SE440BX-2 mobo.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 1/2: cleanups:
o remove i2c read/write wrapper interface as it does nothing,
o change kmalloc + memset to kzalloc
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Proper handling of suspend/resume in the wbsd driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a BPA 100/105 device contains more then one interface then ignore the
additional interfaces, because they are unused.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch contains the big cleanup of the HCI UART driver. The uneeded
header files are removed and their structure declarations are moved into
the protocol implementations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a number of sparse warnings from the latest sparse
snapshot being generated from the drivers/base build. The
main culprits are due to the initialisation functions not
being declared in a header file.
Also, the firmware.c file should include <linux/device.h>
to get the prototype of firmware_register() and
firmware_unregister().
This patch moves the init function declerations from the
init.c file to the base.h, and ensures it is included in
all the relevant c sources. It also adds <linux/device.h>
to the included headers for firmware.c.
The patch does not solve all the sparse errors generated,
but reduces the count significantly.
drivers/base/core.c:161:1: warning: symbol 'devices_subsys' was not declared. Should it be static?
drivers/base/core.c:417:12: warning: symbol 'devices_init' was not declared. Should it be static?
drivers/base/sys.c:253:6: warning: symbol 'sysdev_shutdown' was not declared. Should it be static?
drivers/base/sys.c:326:5: warning: symbol 'sysdev_suspend' was not declared. Should it be static?
drivers/base/sys.c:428:5: warning: symbol 'sysdev_resume' was not declared. Should it be static?
drivers/base/sys.c:450:12: warning: symbol 'system_bus_init' was not declared. Should it be static?
drivers/base/bus.c:133:1: warning: symbol 'bus_subsys' was not declared. Should it be static?
drivers/base/bus.c:667:12: warning: symbol 'buses_init' was not declared. Should it be static?
drivers/base/class.c:759:12: warning: symbol 'classes_init' was not declared. Should it be static?
drivers/base/platform.c:313:12: warning: symbol 'platform_bus_init' was not declared. Should it be static?
drivers/base/cpu.c:110:12: warning: symbol 'cpu_dev_init' was not declared. Should it be static?
drivers/base/firmware.c:17:5: warning: symbol 'firmware_register' was not declared. Should it be static?
drivers/base/firmware.c:23:6: warning: symbol 'firmware_unregister' was not declared. Should it be static?
drivers/base/firmware.c:28:12: warning: symbol 'firmware_init' was not declared. Should it be static?
drivers/base/init.c:28:13: warning: symbol 'driver_init' was not declared. Should it be static?
drivers/base/dmapool.c:174:10: warning: implicit cast from nocast type
drivers/base/attribute_container.c:439:1: warning: symbol 'attribute_container_init' was not declared. Should it be static?
drivers/base/power/runtime.c:76:6: warning: symbol 'dpm_set_power_state' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Input: remove custom-made hotplug handler
Now that all input devices are registered with sysfs we can remove
old custom-made hotplug handler and crate a standard one.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This creates symlinks in /sys/class/input/ to the nested class devices
to help userspace cope with the nesting.
Unfortunatly udev still needs to be updated as it can't handle symlinks
properly here :(
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Input: show sysfs path in /proc/bus/input/devices
Show that sysfs and phys path are different objects.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows struct class_device to be nested, so that another
struct class_device can be the parent of a new one, instead of only
having the struct class be the parent. This will allow us to
(hopefully) fix up the input and video class subsystem mess.
But please people, don't go crazy and start making huge trees of class
devices, you should only need 2 levels deep to get everything to work
(remember to use a class_interface to get notification of a new class
device being added to the system.)
Oh, this also allows us to have the possibility of potentially, someday,
moving /sys/block into /sys/class. The main hindrance is that pesky
/dev numberspace issue...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A "coldplug + udevstart" can be simple like this:
for i in /sys/block/*/*/uevent; do echo 1 > $i; done
for i in /sys/class/*/*/uevent; do echo 1 > $i; done
for i in /sys/bus/*/devices/*/uevent; do echo 1 > $i; done
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: pass interface to class intreface methods
Pass interface as argument to add() and remove() class interface
methods. This way a subsystem can implement generic add/remove
handlers and then call interface-specific ones.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2O: cleanup - remove i2o_device_class
I2O devices reside on their own bus so there should be no reason
to also have i2c_device class that mirros i2o bus.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2O: remove i2o_device_class_interface misuse
The intent of class interfaces was to provide different
'views' at the same object, not just run some code every
time a new class device is registered. Kill interface
structure, make class core register default attributes
and set up sysfs links right when registering class
devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move call to kobject_hotplug() above code that adds interfaces
to a class device, otherwise children's hotplug events may reach
userspace first.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch teaches "usb_device" about the new driver model wakeup support:
- It updates device wakeup capabilities when entering a configuration
with the WAKEUP attribute;
- During suspend processing it consults the policy bit to see
whether it should enable wakeup for that device. (This resolves
a FIXME to not assume the answer is always "yes"; some devices
lie about supporting remote wakeup.)
Support for root hubs and the HCDs is separate (and more complex).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a refresh of an earlier patch to add "wakeup" support to the
PM core model. This provides per-device bus-neutral control of the
use of wakeup events.
* "struct device_pm_info" has two bits that are initialized as
part of setting up the enclosing struct device:
- "can_wakeup", reflecting hardware capabilities
- "may_wakeup", the policy setting (when CONFIG_PM)
* There's a writeable sysfs "wakeup" file, with one of two values:
- "enabled", when the policy is to allow wakeup
- "disabled", when the policy is not to allow it
- "" if the device can't currently issue wakeups
By default, wakeup is enabled on all devices that support it. If its
driver doesn't support it ... treat it as a bug. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was recently given an old Travan tape drive and asked to do something
useful with it. The ide-scsi + st (+serverworks ide controller) combo
results in a hard lockup of the machine which I have not had the energy to
debug, so I turned to ide-tape (which seems to work). The system in
question debian stable, using udev to manage /dev.
The following patch to ide-tape.c allows udev to create the cdev nodes for
my drive.
Cc: Gadi Oxman <gadio@netvision.net.il>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use get_unaligned for possibly-unaligned multi-byte accesses to the
ATA device identify response buffer.
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
This adds support for the RTC and nvram on the Comdial MP1000
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
This patch gives support for the CS8900A ethernet chip on the Comdial MP1000
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
Updated 2898/1 per comments:
- Removed fixup
- Moved code in mach-mp1000/ to mach-clps711x/
- Cleaned up code in mp1000-seprom.c. Eliminated code that displayed the contents of the eeprom
Please comment.
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ian Campbell
The sparse warning initially surfaced in sound/arm/pxa2xx-ac97.c
because it was using u32 * variables to hold the unsigned long *
register addresses.
I submitted an ALSA patch for this http://thread.gmane.org/gmane.linux.alsa.devel/27804 issue and it was suggested that it might be preferable to change the register
definitions to use u32.
Most other subarches seem to use u32 for their register type, at least
the ones which use a __REG macro (like the PXA) do. Nico indicated in
the thread above that he wouldn't mind this patch.
Changing the type required fixes for opposite warnings in the pxa2xx usb
gadget code but that was the only new warning introduced on defconfig
or lubbock, mainstone and our own PXA255 boards.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warnings in arch/arm/kernel/module.c,
arch/arm/mm/consistent.c, drivers/pcmcia/sa1111_generic.c,
and platform support files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
EBSA110 only requires hardware.h to be included for a couple of
files. Move the include there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- 100msec sleep is a little excessive, lots of requests can complete
in that timeframe. Use 10msec instead.
- Rename QUEUE_FLAG_BYPASS to QUEUE_FLAG_ELVSWITCH to indicate what
is going on.
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch reimplements elevator switch. This patch assumes generic
dispatch queue patchset is applied.
* Each request is tagged with REQ_ELVPRIV flag if it has its elevator
private data set.
* Requests which doesn't have REQ_ELVPRIV flag set never enter
iosched. They are always directly back inserted to dispatch queue.
Of course, elevator_put_req_fn is called only for requests which
have its REQ_ELVPRIV set.
* Request queue maintains the current number of requests which have
its elevator data set (elevator_set_req_fn called) in
q->rq->elvpriv.
* If a request queue has QUEUE_FLAG_BYPASS set, elevator private data
is not allocated for new requests.
To switch to another iosched, we set QUEUE_FLAG_BYPASS and wait until
elvpriv goes to zero; then, we attach the new iosched and clears
QUEUE_FLAG_BYPASS. New implementation is much simpler and main code
paths are less cluttered, IMHO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch kills max_back_kb handling from elv_dispatch_sort() and
kills max_back_kb field from struct request_queue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Currently, both generic elevator code and specific ioscheds
participate in the management and usage of last_merge. This
and the following patches move last_merge handling into
generic elevator code.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch updates all four ioscheds to use generic dispatch
queue. There's one behavior change in as-iosched.
* In as-iosched, when force dispatching
(ELEVATOR_INSERT_BACK), batch_data_dir is reset to REQ_SYNC
and changed_batch and new_batch are cleared to zero. This
prevernts AS from doing incorrect update_write_batch after
the forced dispatched requests are finished.
* In cfq-iosched, cfqd->rq_in_driver currently counts the
number of activated (removed) requests to determine
whether queue-kicking is needed and cfq_max_depth has been
reached. With generic dispatch queue, I think counting
the number of dispatched requests would be more appropriate.
* cfq_max_depth can be lowered to 1 again.
Original from Tejun Heo, modified version applied.
Signed-off-by: Jens Axboe <axboe@suse.de>
Implements generic dispatch queue which can replace all
dispatch queues implemented by each iosched. This reduces
code duplication, eases enforcing semantics over dispatch
queue, and simplifies specific ioscheds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch removes try_module_get race in elevator_find.
try_module_get should always be called with the spinlock protecting
what the module init/cleanup routines register/unregister to held. In
the case of elevators, we should be holding elv_list to avoid it going
away between spin_unlock_irq and try_module_get.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
disk stat when "now" is different from disk->stamp. Otherwise, we
are again needlessly adding zero to the stats.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
struct gendisk has these two fields: stamp, stamp_idle. Update to
stamp_idle is always in sync with stamp and they are always the same.
Therefore, it does not add any value in having two fields tracking
same timestamp. Suggest to remove it.
Also, we should only update gendisk stats with non-zero value.
Advantage is that we don't have to needlessly calculate memory address,
and then add zero to the content.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Don't try to access not-present CPUs. Conservative governor will always
oops on SMP without this fix.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=4781
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've seen similar failure on alpha.
Obviously, someone forgot to convert sg->handle stuff for
PCI gart case.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are still a couple of cases where md threads (the resync/recovery
thread) is not interruptible since the change to use kthreads. All places
there it tests "signal_pending", it should also test kthread_should_stop,
as with this patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When reserving an PCI quirk, note that in the kernel bootup messages.
Also, parse the strange PIIX4 device resources - they should get their
own PCI resource quirks, but for now just print out what it finds to
verify that the code does the right thing.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If qla2x00_probe_one()'s call to qla2x00_iospace_config() fails, we call
qla2x00_free_device() to clean up. But because ha->dpc_pid hasn't been set
yet, qla2x00_free_device() tries to stop a kernel thread which hasn't started
yet. It does wait_for_completion() against an uninitialised completion struct
and the kernel hangs up.
Fix it by initialising ha->dpc_pid a bit earlier.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct some function names in kernel-doc.
Add some kernel-doc descriptions.
Fix some typos.
Remove a few blank lines.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This small patch returns the stride/line length of the framebuffer via
sysfs.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event cause
register (ECR), even if we didn't find any entries in the EQ. If we don't,
then there's a window where we miss an EQ entry and then get stuck because
we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That's what we've always historically done, and bigger windows seem to
confuse some cardbus bridges. Or something.
Alan reports that this makes the ThinkPad 600x series work properly
again: the 4kB IO window for some reason made IDE DMA not work, which
makes IDE painfully slow even if it works after DMA timeouts.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Newer hardware doesn't corrupt data when the queue depth
is greater than one. Rather than force the user to recompile
with a greater queue depth, make it a module parameter.
* update copyright date
* add MODULE_VERSION()
* trim trailing whitespace
* move CARM_SG_BOUNDARY to a separate enum, since its unsigned long
* bump to version 1.0
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Missing spin_lock_init() made the Mux driver hang on SMP systems.
Fix up users of ->hpa to use ->hpa.start instead
Remove warning in 8250_gsc.c by eliminating serial_line_nr
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
add netpoll support
Patch by Sven Schnelle <svens@gmx.de>
Signed-off-by: Sven Schnelle <svens@gmx.de>
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
git commit 976ecd12b8 changed our locking
characteristics, and put the onus of spin_lock_init on superio.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc1-pa6 use work queue in LED/LCD driver instead of tasklet.
Main advantage is it allows use of msleep() in the led_LCD_driver to
"atomically" perform two MMIO writes (CMD, then DATA).
Lead to nice cleanup of the main led_work_func() and led_LCD_driver().
Kudos to David for being persistent.
From: David Pye <dmp@davidmpye.dyndns.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix some whitespace issues
Reorganise parisc_device probe routine to be a little less convoluted
Use ->hpa.start instead of ->hpa
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
add || STI_CONSOLE to some of the basic FONTs. May need to get at
least one of them to default to "Y" for parisc.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix card-mode Dino crashes on 725 (and probably other Snake) systems.
Dino was coming up in fatal mode after a warm reboot. Resetting Dino
brings it out of fatal mode, so do that if the status register indicates
we're in fatal mode. Since this was never observed on any later systems,
I presume firmware does this for us on those.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Add debug statements in the cfg_read and cfg_write functions
Fix debug statements from the IRQ overhaul last winter
Rename dino_driver_callback() to dino_probe()
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 fdc/lci should be %r0 instead 0 for index (PA 1.1 compliance)
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Explain why we need insert_resource() instead of request_resource().
Fundementally, this is more convoluted for ccio driver because of
o legacy (HP-PB) transperant bridges.
o support for MMIO behind card-mode Dino (PCI)
o support for above bridges without ccio in the box
SBA driver doesn't have to worry about those issues.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Use insert_resource instead of request_resource now that the subdevices
will already have their resources claimed
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
re-enable use of "inline" for perf critical functions.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa5 fix sign extension of MMIO range
Fixes the problem of claiming a range that is disabled on 64-bit kernel:
ccio_init_resource() claimed CCIO bus address space (ffffffff00000000,
ffffffffffffffff)
also removes use of __FILE__.
Tested on both 32 and 64-bit systems by Joel.
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc1-pa7 incorrect BUG_ON in ccio
ccio-dma.c line 1317 was preventing K-class with 4GB RAM from booting.
Any ccio machine with >=2GB of RAM would have (incorrectly) triggered this.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Convert to ioremap and __raw_read/write
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 move "sync" outside the main loop that fills IO Pdir.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove explicit use of sr0 in fdc ops.
Thanks to Joel Soete for reminding me were I added those...
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa2 - make SBA more anal about invalidating pdir entries
Previous code cleared the valid flag a pdir entry but it did NOT
guarantee this change was visible to the PDIR before writing
the PCOM register. Ie the SBA could pick up a stale entry if
the write happened to hit the SBA before the cacheline was flushed
from the cache.
Long term, I think I want to make this a compile time flag.
Developement tree should enable anal pdir checking by default
and Debian can disable it with either a CONFIG option
or one-line patch. fdc/sync options can only negatively affect
performance though I haven't measure how much yet.
If someone can run netperf TCP_RR across gige and compare
-pa1 and -pa2, that would be sufficient.
Cleaned up the use of "fdc" to make sure it's using "kernel"
space id (specify sr0 but maps to sr4-7). It seems a bit fragile
to assume "sr1" gets loaded with KERNEL_SPACE which is how the
code works today.
Tested on 32 and 64-bit SMP kernels on j6k.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove PDC_NARROW from SBA and document history of PDC_NARROW a bit.
It will still show up in an older kernel's .config file.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
if/ifdef cleanups from Joel Soete.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa2 fix 32-bit support for Astro platforms
o Since my last SBA code change, SBA could allocate more than 1GB of IOVA
space on Astro boxes with more than 1GB of RAM when running 32-bit kernel.
This is bad since IOMMU can only talk to the first 1GB at most.
Kudos to jejb for quickly spotting that bug.
o jejb also noted SBA should *always* reject DMA masks > 32-bits since
DMA-mapping.txt indicates caller should try again with 32-bits.
o off-by-one error when comparing the mask to IOVA space size.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix parse_tree_node. much more needs to be done to fix this file.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Make drivers.c compile based on a patch from Pat Mochel.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix drivers.c to create new device tree nodes when no match is found.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Do a proper depth-first search returning parents before children, using the
new klist infrastructure.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Fixed parisc_device traversal so that pdc_stable works again
Fixed check_dev so it doesn't dereference a parisc_device until it
has verified the bus type
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Use insert_resource() instead of request_mem_region().
Request resources at bus walk time instead of driver probe time.
Don't release the resources as we don't have any hotplug parisc_device
support yet.
Add parisc_pathname() to conveniently get the textual representation
of the hwpath used in sysfs.
Inline the remnants of claim_device() into its caller.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
I noticed that some of the STI regions weren't showing up in iomem.
Reading the STI spec indicated that all STI devices occupy at least 32MB.
So check for STI HPAs and give them 32MB instead of 4kB.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The wrong state emission routines were being called for G550, and
consistent maps weren't correctly mapped...
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes handling of the phy identifiers in mptsas.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
[ split it a pre-2.6.14 portion from Eric's bigger patch ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sata_qstor strays into a nasty area - gcc handling of wide enums is
full of bugs that got fixed between gcc versions creating portability
nightmare. Single-member enums are safe, so are ones that stay within
the range of int or unsigned int. Anything beyond that is asking for
trouble.
Declaration of constants split in two enums, taking the ~0UL one into
a separate enum.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Improve sb1250-mac driver to probe for PHYs at addresses other
than 1, such as the PHYs on BigSur.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff found an endian bug in the Marvell driver (thanks!). Here's the
fix for it.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Driver version, white space, comments, device id & other
Originally posted on 8/31 (and perhaps before)...I think it has not
been committed because the patch from that posting was damaged. I'm
reposting to make sure it gets in... :-)
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Include MII address 0 at the end of the PHY scan. This covers the
entire range of possible MII addresses.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Found in the -rt patch set. The scsi_error thread likely will be in the
TASK_INTERRUPTIBLE state upon exit. This patch fixes this bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In drivers/acpi/glue.c the address of an integer is cast to the address of
an unsigned long. This breaks on systems where a long is larger than an
int --- for a start the int can be misaligned; for a second the assignment
through the pointer will overwrite part of the next variable.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've gotten a report on lkml, of a possible regression in the MGA DRM in
2.6.14-rc4 (since -rc1), I haven't been able to reproduce it here, but I've
figured out some possible issues in the mga code that were definitely
wrong, some of these are from DRM CVS, the main fix is the agp enable bit
on the old code path still used by everyone.....
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The main problem fixes is that in certain situations stopping md arrays may
take longer than you expect, or may require multiple attempts. This would
only happen when resync/recovery is happening.
This patch fixes three vaguely related bugs.
1/ The recent change to use kthreads got the setting of the
process name wrong. This fixes it.
2/ The recent change to use kthreads lost the ability for
md threads to be signalled with SIG_KILL. This restores that.
3/ There is a long standing bug in that if:
- An array needs recovery (onto a hot-spare) and
- The recovery is being blocked because some other array being
recovered shares a physical device and
- The recovery thread is killed with SIG_KILL
Then the recovery will appear to have completed with no IO being
done, which can cause data corruption.
This patch makes sure that incomplete recovery will be treated as
incomplete.
Note that any kernel affected by bug 2 will not suffer the problem of bug
3, as the signal can never be delivered. Thus the current 2.6.14-rc
kernels are not susceptible to data corruption. Note also that if arrays
are shutdown (with "mdadm -S" or "raidstop") then the problem doesn't
occur. It only happens if a SIGKILL is independently delivered as done by
'init' when shutting down.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes all spinlocks that can be held during an irq handler to disable
interrupts while the lock is held. Changes spin_[un]lock_irq to use the
irqsave/irqrestore variants for robustness and readability.
In raw1394.c:handle_iso_listen(), don't grab host_info_lock at all -- we're
not accessing host_info_list or host_count, and holding this lock while
trying to tasklet_kill the iso tasklet this can cause an ABBA deadlock if
ohci:dma_rcv_tasklet is running and tries to grab host_info_lock in
raw1394.c:receive_iso. Test program attached reliably deadlocks all SMP
machines I have been able to test without this patch.
Signed-off-by: Andy Wingo <wingo@pobox.com>
Acked-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brice Goglin <Brice.Goglin@ens-lyon.org> reports a printk storm from this
driver. Fix.
Acked-by: David Gibson <hermes@gibson.dropbear.id.au>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Found in the -rt patch set. The scsi_error thread likely will be in the
TASK_INTERRUPTIBLE state upon exit. This patch fixes this bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Expand the mask used when reseting the chip to include the GlobalReset
bit. This fix comes from ICPlus and seems to be required for some
cards.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove an if (1) { ... } block in sundance_probe1. Its purpose seems
to be only to allow for delaring some extra local variables. But, it also
adds ugly indentation without adding any meaning to the code.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Checking the skb->len value before calling skb_padto is redundant.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is a (final?) hack to support the odd DMA allocation requirements
of the b44 hardware. The b44 hardware has a 30-bit DMA mask. On x86,
anything less than a 32-bit DMA mask forces allocations into the 16MB
GFP_DMA range. The memory there is somewhat limited, often resulting
in an inability to initialize the b44 driver.
This hack uses streaming DMA allocation APIs in order to provide an
alternative in case the GFP_DMA allocation fails. It is somewhat ugly,
but not much worse than the similar existing hacks to support SKB
allocations in the same driver. FWIW, I have received positive
feedback on this from several Fedora users.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Expand comment explaining MAC address selection for replicated IGMP
frames transmitted in bonding mode 1 (active-backup). Also, a small
whitespace cleanup.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add "HasHltClk" flag for RTL-8100B/8139D hardware in order to fix
problems resuming from suspend-to-RAM.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
work_done is overwritten each time through the rx_action loop in
epic_poll. This screws-up the NAPI accounting if the loop is executed
more than once.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Get rid of the mdelay call in rhine_disable_linkmon. The function
is called from the via-rhine versions of mdio_read and mdio_write.
Those functions are indirectly called from rhine_check_media and
rhine_tx_timeout, both of which can be called in interrupt context.
So, create tx_timeout_task and check_media_task as instances of struct
work_struct inside of rhine_private. Then, change rhine_tx_timeout to
invoke schedule_work for tx_timeout_task (i.e. rhine_tx_timeout_task),
moving the work to process context. Also, change rhine_error (invoked
from rhine_interrupt) to invoke schedule_work for check_media_task
(i.e. rhine_check_media_task), which simply calls rhine_check media
in process context. Finally, add a call to flush_scheduled_work in
rhine_close to avoid any resource conflicts with pending work items.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/e1000/e1000_main.c: In function `e1000_intr':
drivers/net/e1000/e1000_main.c:3156: error: `i' undeclared (first use in this function)
drivers/net/e1000/e1000_main.c:3156: error: (Each undeclared identifier is reported only once
drivers/net/e1000/e1000_main.c:3156: error: for each function it appears in.)
This function is foul.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/declance.c | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
o Add support for DP83847 MII.
o remove unused variable.
o Add some initialisations so even an unknown MII won't result in a crash.
o Correct error message to "no known MIIs found".
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/au1000_eth.c | 13 +++++--------
1 files changed, 5 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
problem:
id[53-58] might be changed after initializing device CHS settings.
changes:
- call ata_dev_reread_id() to reread the identify device info,
after initializing device CHS settings.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If .owner isn't set the module can be unloaded even while still active.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SMACK (Stuttgart Modified Amateurradio CRC KISS) is a KISS variant that
uses CRC16 checksums to secure data transfers between the modem and host.
It's also used to communicate over a pty to applications such as Wampes.
Patches for Linux 2.4 by Thomas Osterried DL9SAU, upgraded to the latest
mkiss 2.6 mkiss driver by me.
Signed-off-by: Thomas Osterried DL9SAU <thomas@x-berg.in-berlin.de>
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From Suzanne Wood <suzannew@cs.pdx.edu>:
Clarify RCU implementation in bpqether.c.
Because bpq_new_device() calls list_add_rcu() and bpq_free_device() calls
list_del_rcu(), substitute list_for_each_entry_rcu() for
list_for_each_entry() in bpq_get_ax25_dev() and in bpq_seq_start().
Add rcu dereference protection in bpq_seq_next().
The rcu_read_lock()/unlock() in bpq_device_event() are removed because
netdev event handlers are called with RTNL locking in place.
FYI: bpq_free_device() calls list_del_rcu() which, per list.h, requires
synchronize_rcu() which can block or call_rcu() or call_rcu_bh() which
cannot block. Herbert Xu notes that synchronization is done here by
unregister_netdevice(). This calls synchronize_net() which in turn uses
synchronize_rcu().
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
