Commit Graph

45 Commits

Author SHA1 Message Date
Jens Rottmann
82f55af06a fix "lxfb: extend PLL table to support dotclocks below 25 MHz"
The following patch caused a regression with OLPC panels:

 commit 3888d4639e
    lxfb: extend PLL table to support dotclocks below 25 MHz

    Extends the PLL frequency table of the AMD Geode-LX frame buffer driver to
    make use of the DIV4 bit, thus adding support for dotclocks between 6 and 25
    MHz.  These are needed for small LCDs (e.g.  320x240).  Also inserts some
    intermediate steps between pre-existing frequencies.

The problem was the insertion of intermediate steps into the frequency
table; they would cause the wrong frequency to be matched.  This patch
drops those intermediate frequencies while keeping the sub-25MHz
frequencies.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jens Rottmann <JRottmann@LiPPERT-AT.de>
Tested-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14 19:11:13 -07:00
Andres Salomon
3553a2fa8c OLPC: gxfb/lxfb: add DCON panel modes to framebuffer drivers
Since there's no way to autodetect panel modes, we're forced to hardcode them
in the driver and add a big fat #ifdef.  The OLPC DCON needs a specific mode
line (at 1200x900).  This adds it to both gxfb and lxfb.

(Jordan said: We could probably detect the panel mode, but there isn't any
reason to since the panel timings are well known and won't change.  While OFW
detection would be good computer science fu, it would be a wasted effort since
its so easy to hard code them into the table.)

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:40 -07:00
Andres Salomon
fd96795630 gxfb/lxfb: detect framebuffer size using an MSR if VSA2 isn't available
If there's no VSA2 (ie, if we're using tinybios or OpenFirmware), use the
GLIU's P2D Range Offset Descriptor to determine how much memory we have
available for the framebuffer.

Originally based on a patch by Jordan Crouse.  Tested with OpenFirmware;
Pascal informs me that tinybios has a stub that fills in P2D_RO0.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:40 -07:00
Andres Salomon
61a517a063 gxfb/lxfb: use VSA definitions when fetching framebuffer size
..Rather than using magic constants.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:40 -07:00
Andres Salomon
4537f93ae8 lxfb/gxfb: when blanking with FB_BLANK_POWERDOWN, also turn off the CRT
The Display Control's CRT_EN can be shut off when we enter FB_BLANK_POWERDOWN
in an attempt to save additional power.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:40 -07:00
Andres Salomon
564820d42a lxfb: disable suspend VT switch by default
By default disable VT switch, but allow it to be overridden via the
'vt_switch' module arg.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
c805df3d62 lxfb: rename kernel arg fbsize to vram
Match other fb drivers (including gxfb).  Also, document the current boot
arguments in Documentation/fb/lxfb.txt.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
f694e53bd0 lxfb: add power management functionality
This adds the ability to suspend/resume the lxfb driver, which includes:
  - Register and palette saving code; registers are stored in lxfb_par.
    A few MSR values are saved as well.
  - lx_powerup and lx_powerdown functions which restore/save registers and
    enable/disable graphic engines.
  - lxfb_suspend/lxfb_resume

Originally based on a patch by Jordan Crouse.

[akpm@linux-foundation.org: be conventional, save an ifdef]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
aec40532c4 lxfb: rearrange/rename MSR bitfields
Finally, move the MSR bitfields around in lxfb.h, and rename them.  Alas, most
of that crap appears to be undocumented.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
31f51fa8d4 lxfb: clean up final bits of df_regs
Finally drop the last remnants of df_regs, using vp_regs instead.  Also, drop
panel_width and panel_height from lxfb_par; they're unused.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
f5c90e85dc lxfb: clean up register definitions
- Rename various bitfield defines to match the data sheet names.
 - Rename DF_ register definitions to VP_ to match the data sheet;
   ie, DF_PAR -> VP_PAR.
 - for GP/DC registers, rather than defining to specific addresses, use
   an enum to number them sequentially and just multiply by 4 (bytes) to
   access them (in read_*/write_* functions).
 - for VP/FP registers, use an enum and multiple by 8 (bytes).  They're
   64bit registers.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
9286361bea lxfb: create GP/DC/VP/FP-specific handlers rather than using readl/writel
This creates read_gp/write_gp, read_dc/write_dc, read_vp/write_vp, and
read_fp/write_fp for reading and updating those registers.  Note that we don't
follow the 'DF' naming; those will be renamed to VP shortly.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Jens Rottmann
3888d4639e lxfb: extend PLL table to support dotclocks below 25 MHz
Extends the PLL frequency table of the AMD Geode-LX frame buffer driver to
make use of the DIV4 bit, thus adding support for dotclocks between 6 and 25
MHz.  These are needed for small LCDs (e.g.  320x240).  Also inserts some
intermediate steps between pre-existing frequencies.

Signed-off-by: Jens Rottmann <JRottmann@LiPPERT-AT.de>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:39 -07:00
Andres Salomon
b6f448e99c PM/gxfb: add hook to PM console layer that allows disabling of suspend VT switch
Prior to suspend, we allocate and switch to a new VT; after suspend, we switch
back to the original VT.  This can be slow, and is completely unnecessary if
the framebuffer we're using can restore video properly.

This adds a hook that allows drivers to select whether or not to do this vt
switch, and changes the gxfb driver to call this hook.  It also adds a module
param to gxfb to allow controlling of the vt switch (defaulting to no switch).

(Note: I'm not convinced that console_sem is the best way to protect this, but
we should probably have some form of locking..)

[akpm@linux-foundation.org: build fix]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
46fb6f110d gxfb: add power management functionality
This adds the ability to suspend/resume the gxfb driver, which includes:
  - The addition of a Graphics Processor register table in gxfb.h, and
    associated GP handling.
  - Register and palette saving code; registers are stored in gxfb_par.
    A few MSR values are saved as well.
  - gx_powerup and gx_powerdown functions which restore/save registers and
    enable/disable graphic engines.
  - gxfb_suspend/gxfb_resume

Originally based on a patch by Jordan Crouse.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
d1b4cc3ec5 gxfb: stop sharing code with gx1fb
We want to stop sharing stuff with gx1fb; it makes little sense.  There were
fields in geodefb_par that weren't being used, there was little point to the
DC/VP ops callbacks, etc.  This implements the following:

  - Create gxfb_par (based on geodefb_par), place it in gxfb.h
  - Drop display_gx.h and video_gx.h.  The last few patches moved most
    stuff into gxfb.h anyways, so there was very little left.
  - Drop the geode_{dc,vid}_ops stuff.  Un-static functions, add
    declarations to gxfb.h.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
9f1277bd14 gxfb: move MSR bit fields into gxfb.h
This continues the gxfb header cleanups.  MSRs are defined in geode.h; the
specific bits we care about are defined in gxfb.h.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
d255114f22 gxfb: clean up register definitions
This does the following in preparation for register saving:
  - moves the register definitions from video_gx.h and display_gx.h into
    gxfb.h.
  - renames GX_* registers to match their section (ie, VP_).
  - renames register bitfields to match the data sheet (ie,
    DC_DCFG_TGEN -> DC_DISPLAY_CFG_TGEN).
  - for DC registers, rather than defining to specific addresses, use
    an enum to number them sequentially and just multiply by 4(bytes) to
    access them (in read_dc/write_dc).
  - for VP and FP registers, use an enum and multiple by 8 (bytes).  They're
    64bit registers.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
ab06aaf6a6 gxfb: create DC/VP/FP-specific handlers rather than using readl/writel
This creates read_dc/write_dc, read_vp/write_vp, and read_fp/write_fp for
reading and updating those registers.  It creates gxfb.h to house these.

We also drop a no-op readl() from gx_set_mode.  Other than that, there should
be no functionality change.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
fa20c8a6e5 gxfb: replace FBSIZE config option with a module parameter
Use a command line option (vram) rather than hardcoding the vram size.  LxFB
already does this; it's useful for machines that can't query the BIOS for fb
size.  This patch originated from David Woodhouse, was modified by Jordan
Crouse, and was then modified further by me.

This also adds some gxfb documentation in Documentation/fb.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Andres Salomon
0a5e790987 gxfb: use PCI_DEVICE() for gxfb's pci device table
Drop the class/class_mask stuff; it's unnecessary as long as the vendor and
device IDs match.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:36 -07:00
Jordan Crouse
e2b1180909 gxfb: don't enable the CRT DACs when we are in flatpanel mode
When the FP strap is enabled, don't turn on the CRT DACs - that will save
about 35 mA of power.

Updated/cleaned up by Andres Salomon.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:35 -07:00
Jordan Crouse
f0a0c1f20f gxfb: set the right registers to tweak the sync polarity
While running in flatpanel mode it is important to change the FP sync bits (VG
register 0x408) rather then the CRT sync bits (VG register 0x008).  This patch
keeps the CRT sync bits at default when a flatpanel exists.

Note that this also fixes inverted logic; we want CRT_VSYNC_POL to be set (ie,
vsync is normally high) when FB_SYNC_VERT_HIGH_ACT is unset.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:35 -07:00
Andres Salomon
32bf87e369 x86: geode: MSR cleanup
This cleans up a few MSR-using drivers in the following manner:
  - Ensures MSRs are all defined in asm/geode.h, rather than in misc
    places
  - Makes the naming consistent; cs553[56] ones begin with MSR_,
    GX-specific ones start with MSR_GX_, and LX-specific ones start
    with MSR_LX_.  Also, make the names match the data sheet.
  - Use MSR names rather than numbers in source code
  - Document the fact that the LX's MSR_PADSEL has the wrong value
    in the data sheet.  That's, uh, good to note.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:35 -07:00
Adrian Bunk
cfe2f714d9 make video/geode/lxfb_core.c:geode_modedb[] static
geode_modedb[] can become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:15 -08:00
Jordan Crouse
62ec56524f LXFB: use the correct MSR number for panel support
A relatively recent version of the Geode LX datasheet listed the wrong
address for one of the MSRs that controls TFT panels, resulting in
breakage.  This patch corrects the MSR address.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-14 18:45:38 -08:00
Mike Travis
92cb7612ae x86: convert cpuinfo_x86 array to a per_cpu array
cpu_data is currently an array defined using NR_CPUS.  This means that
we overallocate since we will rarely really use maximum configured cpus.
When NR_CPU count is raised to 4096 the size of cpu_data becomes
3,145,728 bytes.

These changes were adopted from the sparc64 (and ia64) code.  An
additional field was added to cpuinfo_x86 to be a non-ambiguous cpu
index.  This corresponds to the index into a cpumask_t as well as the
per_cpu index.  It's used in various places like show_cpuinfo().

cpu_data is defined to be the boot_cpu_data structure for the NON-SMP
case.

Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2007-10-19 20:35:04 +02:00
Eugene Teo
42b558d51c drivers/video/geode/lxfb_core.c: fix lxfb_setup warning
drivers/video/geode/lxfb_core.c: In function 'lxfb_setup':
drivers/video/geode/lxfb_core.c:564: warning: unused variable 'opt'

Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:15 -07:00
Jordan Crouse
3968cb49ab lxfb: GEODE: Add framebuffer support for the AMD Geode LX
Add framebuffer support for the AMD Geode LX graphics engine.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31 15:39:37 -07:00
Alexey Dobriyan
c7b54477d3 [PATCH] Recognize video=gx1fb:... option
Juergen Beisert reported that the following option doesn't work for him

	video=gx1fb:1024x768-16@60

though sisfb was able to parse similar option correctly.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-12 09:48:42 -08:00
Jordan Crouse
58219896df [PATCH] gxfb: Turn on the flatpanel power and data
For Geode devices without a flatpanel aware BIOS, this enables the flatpanel
power and data.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Jordan Crouse
53d53bd4ab [PATCH] gxfb: Fixup flatpanel detection
Use the right MSR and bits to detect if the GX is strapped for TFT or CRT

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Jordan Crouse
16ef987095 [PATCH] gxfb: Support command line options
Add support for command line options for setting the mode and various
settings.

[akpm@osdl.org: cleanups]
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Jordan Crouse
ab1db0cfcf [PATCH] gxfb: Support flat panel timings
Support TFT panels by correctly setting up the flat panel registers

[akpm@osdl.org: cleanups]
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Jordan Crouse
f378819a19 [PATCH] gxfb: Fixups for the AMD Geode GX framebuffer driver
We cannot assume that the BIOS will be correctly setting up the hardware, so
set some bits in various display registers to enable video output.  Allow an
advanced user to specify a frambuffer size, rather then probing the BIOS.  All
of these fixes were prompted by the OLPC effort.

[akpm@osdl.org: cleanups]
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Jordan Crouse
4c1979c896 [PATCH] FB: Get the Geode GX frambuffer size from the BIOS
Use the Geode GX BIOS virtual registers to get the actual size of the
framebuffer.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:29:08 -08:00
Jordan Crouse
65867beb0d [PATCH] Trivial cleanup in the PCI IDs for the CS5535
Rename a poorly worded PCI ID for the Geode GX and CS5535 companion chips.
The graphics processor and host bridge actually live in the northbridge on
the integrated processor, not in the companion chip.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:44 -08:00
Jon Smirl
a8f340e394 [PATCH] vt: Remove VT-specific declarations and definitions from tty.h
MAX_NR_CONSOLES, fg_console, want_console and last_console are more of a
function of the VT layer than the TTY one.  Moving these to vt.h and vt_kern.h
allows all of the framebuffer and VT console drivers to remove their
dependency on tty.h.

[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:16 -07:00
Antonino A. Daplas
a06630f3e7 [PATCH] Detaching fbcon: remove calls to pci_disable_device()
Detaching fbcon allows individual drivers to be unloaded.  However several
drivers call pci_disable_device() upon exit.  This function will disable the
BAR's which will kill VGA text mode and/or affect X/DRM.

To prevent this, remove calls to pci_disable_device() from several drivers.

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:32 -07:00
David Vrabel
fc4effc7a9 [PATCH] fbdev: framebuffer driver for Geode GX
A framebuffer driver for the display controller in AMD Geode GX processors
(Geode GX533, Geode GX500 etc.).  Tested at 640x480, 800x600, 1024x768 and
1280x1024 at 8, 16, and 24 bpp with both CRT and TFT.  No accelerated features
currently implemented and compression remains disabled.

This driver requires that the BIOS (or the SoftVG/Firmbase code in the BIOS)
has created an appropriate virtual PCI header.

Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27 08:44:55 -08:00
David Vrabel
a80da73898 [PATCH] gx1fb: (try to) play nicer with various BIOSes
Seems that the CS5530A chip used in Geode GX1 systems has some crazy feature
that causes SMI traps when accessing the PCI configuration space of the video
device.  Various GX1 BIOSes seem to use this 'feature' to hide the real BARs
of the device.  This patch disables these traps (in an early PCI fixup) so
that Linux sees the real, physical BARs and not the virtual ones provided by
the BIOS.

This should allow the GX1 framebuffer driver to work on more systems that have
different BIOSes as the driver no longer guesses at what the virtual BARs
mean.

I'm not entirely sure it the correct solution as I can neither test regular
VGA console nor the X's 'cyrix' video driver so there might be some breakage
there -- probably best to get some more testers before applying it.

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-14 18:27:14 -08:00
Antonino A. Daplas
c465e05a03 [PATCH] fbcon/fbdev: Move softcursor out of fbdev to fbcon
According to Jon Smirl, filling in the field fb_cursor with soft_cursor for
drivers that do not support hardware cursors is redundant.  The soft_cursor
function is usable by all drivers because it is just a wrapper around
fb_imageblit.  And because soft_cursor is an fbcon-specific hook, the file is
moved to the console directory.

Thus, drivers that do not support hardware cursors can leave the fb_cursor
field blank.  For drivers that do, they can fill up this field with their own
version.

The end result is a smaller code size.  And if the framebuffer console is not
loaded, module/kernel size is also reduced because the soft_cursor module will
also not be loaded.

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-07 07:53:50 -08:00
Ingo Molnar
a9f6a0dd54 [PATCH] more SPIN_LOCK_UNLOCKED -> DEFINE_SPINLOCK conversions
This converts the final 20 DEFINE_SPINLOCK holdouts.  (another 580 places
are already using DEFINE_SPINLOCK).  Build tested on x86.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 14:03:48 -07:00
David Vrabel
53eed4ec8b [PATCH] fbdev: geode updates
Geode framebuffer driver updates:

- Local mode list (taken from modedb.c) containing only relevant modes.
  This also makes the driver work as a module.

- Make it a PCI driver (from James Simmons <jsimmons@infradead.org>).

- A few other minor cosmetic bits and pieces.

Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-09 13:57:59 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00