Add a separate config option for ide-8300 host driver instead of depending
on CONFIG_H8300.
This change is a preparation for the future changes and also allows ide-h8300
to be disabled if needed.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Only LWMON, IVMS8, IVML24 and TQM8xxL platforms have the needed
defines (IDE0_BASE_OFFSET and friends) in the platform header file.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add pci_enable_device() to aec62xx probe function
before doing any I/O.
Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR
is 0 and the following inb() causes a kernel oops.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.yu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).
If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.
The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.
Bart: minor cleanups
Signed-off-by: Jonas Stare <jonas.stare@purplescout.se>
CC: Andrew Morton <akpm@linux-foundation.org>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (41 commits)
[XFRM]: Fix leak of expired xfrm_states
[ATM]: [he] initialize lock and tasklet earlier
[IPV4]: Remove bogus ifdef mess in arp_process
[SKBUFF]: Free old skb properly in skb_morph
[IPV4]: Fix memory leak in inet_hashtables.h when NUMA is on
[IPSEC]: Temporarily remove locks around copying of non-atomic fields
[TCP] MTUprobe: Cleanup send queue check (no need to loop)
[TCP]: MTUprobe: receiver window & data available checks fixed
[MAINTAINERS]: tlan list is subscribers-only
[SUNRPC]: Remove SPIN_LOCK_UNLOCKED
[SUNRPC]: Make xprtsock.c:xs_setup_{udp,tcp}() static
[PFKEY]: Sending an SADB_GET responds with an SADB_GET
[IRDA]: Compilation for CONFIG_INET=n case
[IPVS]: Fix compiler warning about unused register_ip_vs_protocol
[ARP]: Fix arp reply when sender ip 0
[IPV6] TCPMD5: Fix deleting key operation.
[IPV6] TCPMD5: Check return value of tcp_alloc_md5sig_pool().
[IPV4] TCPMD5: Use memmove() instead of memcpy() because we have overlaps.
[IPV4] TCPMD5: Omit redundant NULL check for kfree() argument.
ieee80211: Stop net_ratelimit/IEEE80211_DEBUG_DROP log pollution
...
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (56 commits)
Blackfin arch: fix bug when enable uart1 with uart0 disabled => no initial console
Blackfin arch: split apart dump_bfin_regs and merge/remove show_regs from process.c, which was largely duplicated
Blackfin arch: use common __INIT/__FINIT defines rather than setting the .section ourselves to .init.text
Blackfin arch: fix bug when sending signals with the wrong PC, cause gdb get confused
Blackfin arch: Ensure we printk out strings with the proper loglevel
Blackfin arch: Need to specify ax with the .init.text section,
Blackfin arch: Update Kconfig to latest Blackfin silicon datasheets
Blackfin arch: update defconfig files
Blackfin arch: Fix typo, and add ENDPROC - no functional changes
Blackfin arch: convert READY to DMA_READY as it causes build errors in common sound code otherwise
Blackfin arch: add defines for the on-chip L1 ROM of BF54x
Blackfin arch: cplb and map header file cleanup
Blackfin arch: cleanup the cplb declares
Blackfin arch: fix broken on BF52x, remove silly checks on processors for L1_SCRATCH defines
Blackfin arch: add support for working around anomaly 05000312
Blackfin arch: cleanup BF54x header file and add BF547 definition
Blackfin arch: fix building for BF542 processors which only have 1 TWI
Blackfin arch: rename _return_from_exception to _bfin_return_from_exception and export it
Blackfin arch: move EXPORT_SYMBOL() to C files where the symbol is actually defined
Blackfin arch: fix bug NOR Flash MTD mount fail
...
Plip passes a string "name" that is allocated on stack to
parport_register_device. parport_register_device holds the pointer to
"name" and when the registering function exits, it points nowhere.
On some machine, this bug causes bad names to appear in /proc, such as
/proc/sys/dev/parport/parport0/devices/T^/�X^/�, on others, the plip
proc node is completely missing.
The patch also fixes documentation to note this requirement.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netif_rx is meant to be called from interrupts because it doesn't wake
up ksoftirqd. For calling from outside interrupts, netif_rx_ni exists.
This fixes plip to use netif_rx_ni. It fixes the infamous error "NOHZ:
local_softirq_panding 08" that happens on some machines with NOHZ and
plip --- it is caused by the fact that softirq is pending and ksoftirqd
is sleeping.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: Avoid re-using minor numbers before the original device is closed.
tifm_sd: handle non-power-of-2 block sizes
mmc_block: check card state after write
... which I've found on a Sapphire X550 (Silent).
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: bump transfer chunk size if it's odd
libata: Return proper ATA INT status in pata_bf54x driver
pata_ali: trim trailing whitespace (fix checkpatch complaints)
pata_isapnp: Polled devices
pata_hpt37x: Fix cable detect bug spotted by Sergei
pata_ali: Lots of problems still showing up with small ATAPI DMA
pata_ali: Add Mitac 8317 and derivatives
libata-core: List more documentation sources for reference
ata_piix: Invalid use of writel/readl with iomap
sata_sil24: fix sg table sizing
pata_jmicron: fix disabled port handling in jmicron_pre_reset()
pata_sil680: kill bogus reset code (take 2)
ata_piix: port enable for the first SATA controller of ICH8 is 0xf not 0x3
ata_piix: only enable the first port on apple macbook pro
ata_piix: reorganize controller IDs
pata_sis.c: Add Packard Bell EasyNote K5305 to laptops
libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs
libata: use ATA_HORKAGE_STUCK_ERR for ATAPI tape drives
libata: workaround DRQ=1 ERR=1 for ATAPI tape drives
libata: remove unused functions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: fix net driver loop case where we fail to restart
module: fix and elaborate comments
virtio: fix module/device unloading
lguest: Fix uninitialized members in example launcher
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (39 commits)
ACPI: EC: Workaround for optimized controllers (version 3)
ACPI: EC: use printk_ratelimit(), add some DEBUG mode messages
Revert "ACPI: EC: Workaround for optimized controllers"
ACPI: fix two IRQ8 issues in IOAPIC mode
ACPI: Add missing spaces to printk format
cpuidle: fix HP nx6125 regression
cpuidle: add sched_clock_idle_[sleep|wakeup]_event() hooks
cpuidle: fix C3 for no bus-master control case
ACPI: thinkpad-acpi: fix oops when a module parameter has no value
Revert "Fix very high interrupt rate for IRQ8 (rtc) unless pnpacpi=off"
ACPI: EC: Don't init EC early if it has no _INI
Revert "acpi: make ACPI_PROCFS default to y"
Revert "ACPI: add documentation for deprecated /proc/acpi/battery in ACPI_PROCFS"
ACPI: Split out control for /proc/acpi entries from battery, ac, and sbs.
ACPI: Video: Increase buffer size for writes to brightness proc file.
ACPI: EC: Workaround for optimized controllers
ACPI: SBS: Fix retval warning
ACPI: Enable MSR (FixedHW) support for T-States
ACPI: Get throttling info from BIOS only after evaluating _PDC
ACPI: Use _TSS for throttling control, when present. Add error checks.
...
if you are lucky (unlucky?) enough to have shared interrupts, the
interrupt handler can be called before the tasklet and lock are ready
for use.
Signed-off-by: chas williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
AMD Opteron processors before CG revision don't like C-states > 1.
This solves the long standing bugzilla #5303 and probably some more
on affected machines:
http://bugzilla.kernel.org/show_bug.cgi?id=5303
[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
None of the drives I have follows what the standard says about
transfer chunk size. Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.
According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended. However, in reality, none of the
drives I have does that. They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.
In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA. Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes. This causes data corruption and buffer
overruns.
This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte. This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a card has no IRQ then pass no interrupt handler but allow polled
usage.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hopefully there is a better long term solution but for now lets favour
reliability.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems. This patch
updates sg table sizing such that
* One full page is used for PRB + sg table. On 4k page,
this results in 253 sg's.
* Make ATAPI sg block properly sized.
* Make build fail if command block size doesn't equal PAGE_SIZE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are two bugs in disabled port handling.
* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0
The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0. The net result is that cable
is always left at ATA_CBL_UNKNOWN. This results in false 80c
configuration and thus transfer errors.
This patch fixes both bugs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: Len Brown <len.brown@intel.com>
Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure all subchannel handling is done on the slow path workqueue
so that we don't have races between an old subchannel unregistering
and a new subchannel with the same name registering.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Modify the sense id channel program to allow device sensing of pav
alias devices which belong to a base device with ungrouped paths.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
