This patch provides core support for CM-X270 platform.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_gpio_mode() is a universal call that fiddles with the GAFR
(gpio alternate function register.) GAFR does not exist on PXA3
CPUs, but instead the alternate functions are controlled via the
MFP support code.
Platforms are expected to configure the MFP according to their
needs in their platform support code rather than drivers. We
extend this idea to the GAFR, and make the gpio_direction_*()
functions purely operate on the GPIO level.
This means platform support code is entirely responsible for
configuring the GPIOs alternate functions on all PXA CPU types.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version
code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the generic clock support code to fiddle with the CKEN register
and mark pxa_set_cken() deprecated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_lcdclk_frequency_10khz() is now redundant, remove it. Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using the compile-time constant CLOCK_TICK_RATE, select
the clock tick rate at run time. We organise the selection so that
PXA3 automatically falls out with the right tick rate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous implementation was relying on compile time optimizations
based on a constant clock rate. However, support for different PXA
flavors in the same kernel binary requires that the clock be selected at
run time, so here it is.
Let's move this code to a more appropriate location while at it.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reimplements arch/arm/mach-pxa/time.c using a clock_event_device based
on OSMR0. Tested on PXA270, linux-2.6.22+arm:pxa patches.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
the corresponding _suspend functions, thus remove all those ugly
#ifdef .. #endif out of sleep.S
2. move the declarations of those suspend functions to pm.h
note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. introduce a structure pxa_cpu_pm_fns for pxa25x/pxa27x specific
operations as follows:
struct pxa_cpu_pm_fns {
int save_size;
void (*save)(unsigned long *);
void (*restore)(unsigned long *);
int (*valid)(suspend_state_t state);
void (*enter)(suspend_state_t state);
}
2. processor specific registers saving and restoring are performed
by calling the corresponding (*save) and (*restore)
3. pxa_cpu_pm_fns->save_size should be initialized to the required
size for processor specific registers saving, the allocated
memory address will be passed to (*save) and (*restore)
memory allocation happens early in pxa_pm_init(), and save_size
should be assigned prior to this (which is usually true, since
pxa_pm_init() happens in device_initcall()
4. there're some redundancies for those SLEEP_SAVE_XXX and related
macros, will be fixed later, one way possible is for the system
devices to handle the specific registers saving and restoring
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. for common devices across all the pxa variants, the names
are changed to be:
"pxa_device_xxx"
2. for pxa25x or pxa27x specific devices, the names are
changed to be:
"pxa25x_device_xxx", or
"pxa27x_device_xxx"
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows individual CPU support to determine which platform
devices should be registered. Also fix a copy-n-paste bug in
the I2C power platform device entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the RTC management over a suspend/resume cycle. Firstly,
we may not be using the internal RTC for time keeping; some
platforms have an external RTC for this inspite of the PXA having
an internal RTC. Secondly, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the number of dma channels varies between pxa25x and pxa27x, it
introduces some specific code in dma.c. This patch moves the specific
code to pxa25x.c and pxa27x.c and makes dma.c more generic.
1. add pxa_init_dma() for dma initialization, the number of channels
are passed in by the argument
2. add a "prio" field to the "struct pxa_dma_channel" for the channel
priority, and is initialized in pxa_init_dma()
3. use a general priority comparison with the channels "prio" field so
to remove the processor specific pxa_for_each_dma_prio macro, this
is not lightning fast as the original one, but it is acceptable as
it happens when requesting dma, which is usually not so performance
critical
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. use GPIO_IRQ_mask[] to select those bits of interest, actually
only those "unmasked" GPIO IRQs with their corresponding bits
in GPIO_IRQ_mask[] set to "1" should be checked
2. remove #ifdef PXA_LAST_GPIO > 96 .. #endif, GPIO_IRQ_mask[]
is used to mask out the irrelevant bits, so that even though
the GEDR3 on PXA25x is reserved, it will be masked, and the
following code will never run. Another point is that GPIO85-
GPIO95 bits within GEDR2 will also be masked out on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move the GPIO IRQ initialization code to pxa_init_irq_gpio()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. move low IRQ initialization code to pxa_init_irq_low()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define PXA_GPIO_IRQ_BASE to be right after the internal IRQs,
and define PXA_GPIO_IRQ_NUM to be 128 for all PXA2xx variants
2. make the code specific to the high IRQ numbers (32..64) to be
PXA27x specific
3. add a function pxa_init_irq_high() to initialize the internal
high IRQ chip, the invoke of this function could be moved to
PXA27x specific initialization code
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. PXA_IRQ_SKIP is defined to be 7 on PXA25x so that the first IRQ
starts from zero. This makes IRQ numbering inconsistent between
PXA25x and PXA27x. Remove this macro so that the same IRQ_XXXXX
definition has the same value on both PXA25x and PXA27x.
2. make IRQ_SSP3..IRQ_PWRI2C valid only if PXA27x is defined, this
avoids unintentional use of these macros on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_pm_prepare() tried to validate the suspend method type. As
noted in previous commits:
eb9289eb209c372d06cee8c9c50269
the checking of the suspend type in the 'prepare' method is the
wrong place to do this; use the 'valid' method instead. This
means that pxa_pm_prepare() can be entirely removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the pm_ops structure into the PXA25x and PXA27x support
files. Remove the old pxa_pm_prepare() function, and rename
the both pxa_cpu_pm_prepare() functions as pxa_pm_prepare().
We'll fix that later.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_pm_finish() does nothing but return zero. The core code
does nothing with this return value, and will not try to call
the finish method in the pm_ops structure if it is NULL.
Therefore, we can remove this useless function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This update for trizeps4 SoM contains:
- support for new TFT on more recent ConXS evalboard
- correct partition of flash device
- update of "trizeps4_defconfig"
Signed-off-by: Jrgen Schindele (linux@schindele.name)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add IRQF_IRQPOLL for each timer interrupt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lots of places in arch/arm were needlessly including linux/ptrace.h,
resumably because we used to pass a struct pt_regs to interrupt
handlers. Now that we don't, all these ptrace.h includes are
redundant.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
