Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Excerpt from bugzilla entry
http://bugzilla.kernel.org/show_bug.cgi?id=5518
"i386 version of Reboot-through-BIOS is unsafe: it forgets to mask APIC LVT
interrupts before jumping to a BIOS entry point. As a result, BIOS ends up
bombarded with interrupts early on boot. The BIOS does not expect it since
following a "normal" hardware cpu reset, all APIC LVT registers have the
Mask bit (16) set and can't generate interrupts.
For example, the version of Phoenix BIOS used by VMware enables interrupts
for the first time before masking/clearing APIC LVT. The APIC Timer LVT
register is still set up for a timer interrupt delivery with a high vector
from the previous Linux incarnation (0xef in our case). The BIOS has not
fully initialized its IDT at this point and the real mode gate for 0xef
remains all zeros. Vector 0xef dispatches BIOS to address 0:0, BIOS takes
a #GP and eventually hangs.
machine_shutdown() does attempt to shut down APIC before jumping to BIOS,
but it is ineffective"
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SH7705 in extended cache mode has some left-over VALID_PAGE() cruft that it
checks when doing lazy dcache write-back. This has been gone for some time
(the last bits were in the discontig code, which should now also be gone --
this also fixes up a build error in the non-discontig case).
pfn_valid() gives the desired behaviour, so we switch to that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was only one board using this (hp690 specifically), and it just so
happens that it's only physically discontiguous at the "normal" P1 offset. If
we bump up the P1 offset, it's possible to hit a shadowed region of memory
where we suddenly become magically contiguous.
As people have been using this shadowed region workaround for quite some time
(and without any adverse effects), it's time to drop the left over discontig
bits that no longer have any practical use (it was always very much
hp690-centric to begin with).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the relatively quirky (ie, not in line with any known
documentation, and amazed it works at all) SuperHyway implementation on
SH4-202. This depends on the earlier SuperHyway patch for multiple block
support and VCR refactoring.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sh had its own support for embedding ramdisk images in to the kernel binary,
but people are using initramfs for this now, so we drop the ramdisk embedding.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kconfig patch needed by fs_enet to work. Works like CONFIG_CPM2.
Cc: Kumar <kumar.gala@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This missing initrd header slipped though last time.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On PPC405GP/GPR it should be possible to enable PCI support, even when the
internal PCI arbiter is disabled (e.g. when using an external PCI
arbiter). The removed code didn't allow this, and also generated a warning
on PPC405EP platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup PPC40x eval boards (bubinga, walnut and sycamore) to support U-Boot
as bootloader. The OpenBIOS bd_info struct is not used in the kernel
anymore (only U-Boot now).
uImage (U-Boot) tested on walnut, sycamore and bubinga
zImage (OpenBIOS) tested on sycamore, bubinga and ebony
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the AMCC PowerPC 440SPe SoC, including PCI Express in root
port mode.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SP SoC has two Processor Local Bus (PLB) segments (a
high-throughput segment and a low-latency segment). Fix our PLB register
definitions to cope with this, and add code to dump the status of both
segments when a machine check occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SPe supports up to 16 GB of RAM, and therefore its IO registers
are at 0x4_xxxx_xxxx instead of being at 0x1_xxxx_xxxx like most other PPC 440
chips. To allow for this, this patch moves the definition of the ERPN used
for mapping UART0 from being hard-coded in the head_44x.S assembly code to
being defined in ibm44x.h.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds watchdog, RTC support for Marvell EV64360BP board.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops, some last minute changes caused the 64K pages patch to break ppc32
build, this fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zImage wrapper has a bug where it doesn't claim() the memory for the
kernel properly, it forgets to take into account the offset between the ELF
header and the kernel itself. This results on some machines, like G5s,
into a kernel that crashes at boot when clearing the BSS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two CONFIG_SMP=n build fixes due to missing <asm/smp.h> includes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current ia64 implementation of dma_get_cache_alignment does not work
for modules because it relies on a symbol which is not exported. Direct
access to a global is a little ugly anyway, so this patch re-implements
dma_get_cache_alignment in a manner similar to what is currently used for
x86_64.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch, however, should be applied on top of the 64k-page-size patch to
fix some problems with hugepage (some pre-existing, another introduced by
this patch).
The patch fixes a bug in the SLB miss handler for hugepages on ppc64
introduced by the dynamic hugepage patch (commit id
c594adad56) due to a misunderstanding of the
srd instruction's behaviour (mea culpa). The problem arises when a 64-bit
process maps some hugepages in the low 4GB of the address space (unusual).
In this case, as well as the 256M segment in question being marked for
hugepages, other segments at 32G intervals will be incorrectly marked for
hugepages.
In the process, this patch tweaks the semantics of the hugepage bitmaps to
be more sensible. Previously, an address below 4G was marked for hugepages
if the appropriate segment bit in the "low areas" bitmask was set *or* if
the low bit in the "high areas" bitmap was set (which would mark all
addresses below 1TB for hugepage). With this patch, any given address is
governed by a single bitmap. Addresses below 4GB are marked for hugepage
if and only if their bit is set in the "low areas" bitmap (256M
granularity). Addresses between 4GB and 1TB are marked for hugepage iff
the low bit in the "high areas" bitmap is set. Higher addresses are marked
for hugepage iff their bit in the "high areas" bitmap is set (1TB
granularity).
To avoid conflicts, this patch must be applied on top of BenH's pending
patch for 64k base page size [0]. As such, this patch also addresses a
hugepage problem introduced by that patch. That patch allows hugepages of
1MB in size on hardware which supports it, however, that won't work when
using 4k pages (4 level pagetable), because in that case hugepage PTEs are
stored at the PMD level, and each PMD entry maps 2MB. This patch simply
disallows hugepages in that case (we can do something cleverer to re-enable
them some other day).
Built, booted, and a handful of hugepage related tests passed on POWER5
LPAR (both ARCH=powerpc and ARCH=ppc64).
[0] http://gate.crashing.org/~benh/ppc64-64k-pages.diff
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to set the shared memory attribute in the page tables
on SMP systems to allow the cache coherency to operate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define ppc_md.set_dabr for both 32 + 64 bit. Cleanup the implementation for
pSeries also, it was needlessly complex. Now we just do two firmware tests at
setup time, and use one of two functions, rather than using one function and
testing on every call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly this involves adding #include <asm/smp.h>, since that defines
things like boot_cpuid[_phys] and [gs]et_hard_smp_processor_id, which
are SMP-related but still needed on UP. This incorporates fixes
posted by Olof Johansson and Heikki Lindholm.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose. The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.
This patch removes the last traces of this mechanism.
Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add nicer printing of faulting address on unresolvable kernel faults.
Makes life a little easier for those who don't know how to decode our
register contents at oops time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds exception table entries for I/O instructions on and
changes MachineCheckException() slightly to cover 8xx specifics (on
8xx the MCE can be generated while executing the IO access instruction
itself, which is not the case on PowerMac's, as the comment on traps.c
details).
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch against m8xx_wdt.c adds <asm/io.h> (required for
out,in_be32/16) and fixes syntatic problems introduced with the IO
accessor macro update.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
setup_irq() aborts immediately if there's no handler for the IRQ in
question. So i8259_init() should set up its handlers before trying to
set up the cascade on IRQ 2.
With this and the patch I sent a few days ago to fix initrd on ppc32, my
Pegasos now runs the arch/powerpc kernel.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch contains the arch/ppc64 bits for enabling DLPAR and PCI
Hotplug for the new OF-based PCI probe mechanism. This code path is
currently broken.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K. The resulting kernel still boots on any
hardware. On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.
Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
glibc expects to count lines beginning with "processor" to determine
the number of processors, not lines beginning with "Processor". So,
give glibc the format it expects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't want to call dump_cpu_info() from cpu_init() after boot since
it produces a lot of unnecessary noise - since cpu_init() gets called
on resume and hotplug cpu insertion events.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.
The init call is made slightly earlier to give machine code an init
level to override them in removing any race.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Since we know the value of cpsr on entry, we can replace the bic+orr with
a single eor. Also remove a possible result delay (at least on XScale).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Make the uengine loader use ixp2000_reg_wrb in the right places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch fixes AHB/PCI endianness problems when the
processor is in little-endian mode.
The patch configures the CSR register closely following the directives
in [1], paragraph 4.1, page 19.
According to the considerations in [1], page 11, while the AHB bus
supports both endian modes, on the IXP4XX it always uses big-endian.
The PCI bus is connected to the South AHB. A wrong setting in the CSR
register will thus cause a malfunctional PCI bus.
A schematic diagram of the bus interconnections on the IXP4XX
can be found in [1], page 18.
The patch has been verified to work on the NSLU2 in
both LE and BE modes.
The author is Peter Korsgaard.
[1] Intel IXP4XX Product Line of Network Processors and IXC1100
Control Plane Processor:
Understanding Big Endian and Little Endian Modes
http://www.intel.com/design/network/applnots/25423701.pdf
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
my patch "x86: initialise tss->io_bitmap_owner to something" (commit ID
d5cd4aadd3) introduced a problem with a
program (DOSEMU) that called ioperm after already doing some port i/o.
The problem is that a process switch return causes tss->io_bitmap_base
to be set to IO_BITMAP_OFFSET so that the fault (that *really* sets the
io bitmap) never triggers.
This fixes that regression.
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit. With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000. Oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Nicolas Pitre
We have an optimized sha1 routine (arch/arm/lib/sha1.S) meant to
override the generic one in lib/sha1.c.
Unfortunately lib/lib.a is listed _before_ arch/arm/lib/lib.a in the
link argument list and therefore the architecture specific lib functions
are not picked up before the generic versions.
This patch is a quick fix to change that ordering for ARM. Here's what
the kbuild maintainer had to say about it (was also CC'd on lkml):
On Wed, 2 Nov 2005, Sam Ravnborg wrote:
> This looks like an obvious way to achive correct ordering.
> We could change it so arch defines always took precedence but
> the above is so simple that it is not worth the effort.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Jiang
This provides support for IXP2xxx error interrupt handling. Previously there was a patch to remove this (although the original stuff was broken). Well, now the error bits are needed again. These are used extensively by the micro-engine drivers according to Deepak and also we will need it for the new EDAC code that Alan Cox is trying to push into the main kernel.
Re-submit of 3072/1, generated against git tree pulled today. AFAICT, this git tree pulled in all the ARM changes that's in arm.diff. Please let me know if there are additional changes. Thx!
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
ARM processors that have pld instructions are not using those copy_user
implementation anymore. Let's remove the useless PLD lines which were
half wrong anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Restrict CONFIG_SGI_SN_XP to IA64_GENERIC or IA64_SGI_SN2 kernels.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
IXDP2401 config file has wrong baudrate and both boards have 3 UARTs.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Using a llx format to print addresses that might possibly be (only) 36
bits wide make sense. However making it a zero padded 16 char wide
field is a bit excessive and useless.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 'K' extension adds several new instructions to the ARMv6 ISA
which are primerily useful for SMP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
register_vpa() doesn't actually do a VPA register call it just uses the flags
you pass it, so rename it to vpa_call() to be clearer.
We can then define register_vpa() and unregister_vpa() which are both simple
wrappers around vpa_call(). (we'll need unregister_vpa() for kexec soon)
We can then cleanup vpa_init(), and because vpa_init() is only called from
platforms/pseries we remove the definition in asm-ppc64/smp.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This adds missing header and thus fix the warning issued by ming prototype.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current comment on top of m8xx_cpm_dpinit is wrong.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently there is no Kconfig symbol to indicate that we want nvram
support on 64-bit kernels; it's assumed we always want it, so make
the powermac setup code always initialize the pmac nvram code if
64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The latest updates to bug.h generate build warnings in traps.c in
arch/ppc. Fix print format specifiers to account for change of line type
to long from int.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The extraction of PCI stuff from struct device_node left some false
assumptions in notifier code. As a result, dynamic add crashes when
non-PCI nodes are added. This patch fixes these assumptions.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we set the kernel entry point and the address of the text
section in the Makefile, using CONFIG_KERNEL_START.
But we've already got <asm/page.h> in the linker script, so we can just
use KERNELBASE directly. That means if we ever change KERNELBASE there's
one less place to change it.
And we can set the entry point with ENTRY().
There are zero differences from "readelf -a vmlinux" with or without this
patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
There's some debugging in prom.c that wraps nastly on 80 character
terminals, reformat it to fit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Merge include/asm-ppc/kexec.h and include/asm-ppc64/kexec.h.
The only thing that's really changed is that we now allocate crash_notes
properly on PPC32. It's address is exported via sysfs, so it's not correct
for it to be a pointer.
I've also removed some of the "we don't use this" comments, because they're
wrong (or perhaps were referring only to arch code).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move plpar_wrappers.h into arch/powerpc/platforms/pseries, fixup white space,
and update callers.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move pSeries specific code in set_dabr() into a ppc_md function, this will
allow us to keep plpar_wrappers.h private to platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Copy default configs into arch/powerpc/configs, rename bpa_defconfig to
cell_defconfig while we're at it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This fixes the x86-64 find_[first|next]_zero_bit() function for the
end-of-range case. It didn't test for a zero size, and the "rep scas"
would do entirely the wrong thing.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since
cell wants them as well as pseries (and chrp can use rtas-proc.c too,
at least in principle). rtas_fw.c is gone, with its bits moved into
rtas_flash.c and rtas.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
3016/1 changed the map_desc structure to take a PFN instead of a
physical address. Fixup Realview machine support for this change.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that without the extra tlb flush, we may end up faulting
during the early kernel initialisation because the TLB can't see
the updated page tables.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include asm/rtas.h for prototype for rtas_call etc., and make the
`done' variable unsigned int since that's what rtas_call wants.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This section of code calls .audit_syscal_exit, but is inside CONFIG_AUDIT,
so it will fail to build if CONFIG_AUDITSYSCALL is not defined.
After discussion with David Woodhouse, change the ifdef to
CONFIG_AUDITSYSCALL
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated m68knommu defconfig. Part of changing the "Motorola" names
to their new name "Freescale".
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't really understand why gcc gives the error it does, but without
this patch, when building with CONFIG_HOTPLUG=n, I get errors like:
CC arch/x86_64/pci/../../i386/pci/fixup.o
arch/x86_64/pci/../../i386/pci/fixup.c: In function `pci_fixup_i450nx':
arch/x86_64/pci/../../i386/pci/fixup.c:13: error: pci_fixup_i450nx causes a section type conflict
The change is obviously correct: an array should be declared
__devinitdata rather that __devinit.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Martin J. Bligh <mbligh@mbligh.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days, the NACA only exists on iSeries. Therefore, this patch
moves naca.h from include/asm-ppc64 to arch/powerpc/platforms/iseries.
There was one file including naca.h outside of platforms/iseries -
arch/ppc64/kernel/udbg_scc.c. However, that's obviously a hangover
from older days. The include is not necessary, so this patch simply
removes it.
Built and booted on iSeries, built for G5 (which uses udbg_scc.o).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/dart.h is included in exactly one place -
arch/powerpc/sysdev/u3_iommu.c. This patch, therefore, moves it into
arch/powerpc/sysdev. While we're at it, update the #ifndef/#define
protecting the include, and the filename in the comments of
u3_iommu.c.
Built and booted on pSeries and G5, built for ppc32 powermac.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This simplifies the macros which are different between 32-bit and
64-bit. It also fixes a couple of printks on the bug->line element,
which is now a long.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were getting powerbook sleep code included, and giving compile
errors, with CONFIG_PM=y on a 64-bit build. This excludes that code
so the kernel will compile. One day BenH will implement on sleep on
the G5...
Signed-off-by: Paul Mackerras <paulus@samba.org>
A couple of instances of "i" that needed to be changed to "cpu_id"
got missed in the merge, because they were in CONFIG_TAU code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The nvram driver imported from the ppc code uses call_rtas, but
rtas_call is the name we are using in merged code (since ppc64 used
that name, and it uses far more RTAS calls than ppc32).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Deepak Saxena
CONFIG_MACH_GTWX5715 hardcodes the machine type in head-xscale.S so we
can no longer boot on any other machine types. The proper fix would be
to remove the hardcoding, but that machine is an off-the-shelf system
and most users won't have access to the bootloader. :(
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds a microcode loader for the ixp2000 architecture.
The ixp2000 is an xscale-based CPU with a number of additional small
CPUs ('microengines') on die that can be programmed to do various
things. Depending on the ixp2000 model, there are between 2 and 16
microengines.
This code provides an API that allows configuring the microengines,
loading code into them, and starting and stopping them and reading
out a number of status registers, and is used by the microengine
network driver that was recently announced to netdev.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch provides a preemption safe implementation of copy_to_user
and copy_from_user based on the copy template also used for memcpy.
It is enabled unconditionally when CONFIG_PREEMPT=y. Otherwise if the
configured architecture is not ARMv3 then it is enabled as well as it
gives better performances at least on StrongARM and XScale cores. If
ARMv3 is not too affected or if it doesn't matter too much then
uaccess.S could be removed altogether.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch provides a new implementation for optimized memory copy
functions on ARM. It is made of two levels: a template that consists of
the core copy code and separate files that define macros to be used with
the core code depending on the type of copy needed. This allows for best
performances while sharing the same core for implementing memcpy(),
copy_from_user() and copy_to_user() for instance.
Two reasons for this work:
1) the current copy_to_user/copy_from_user implementation assumes no
task switch will ever occur in the middle of each copied page making
it completely unsafe with CONFIG_PREEMPT=y.
2) current copy implementations are measurably suboptimal and optimizing
different implementations separately is a pain and more opportunities
for bugs.
The reason for (1) is the fact that copy inside user pages are performed
with the ldm instruction which has no mean for testing user protections
and could possibly race with process preemption bypassing the COW mechanism
for example. This is a longstanding issue that we said ought to be fixed
for about two years now. The solution is to substitute those ldm insns
with a series of ldrt or strt insns to enforce user memory protection.
At least on StrongARM and XScale cores the ldm is not faster than the
equivalent ldr/str insns with a warm i-cache so there is no measurable
performance degradation with that change. The fact that the copy code is
a template makes it pretty easy to reuse the same core code as for memcpy
and benefit from the same performance optimizations.
Now (2) is best demonstrated with actual throughput measurements.
First, here is a summary of memcopy tests performed on a StrongARM core:
PTR alignment buffer size kernel version this version
------------------------------------------------------------
aligned 32 59.73 107.43
unaligned 32 61.31 74.72
aligned 100 132.47 136.15
unaligned 100 103.84 123.76
aligned 4096 130.67 130.80
unaligned 4096 130.68 130.64
aligned 1048576 68.03 68.18
unaligned 1048576 68.03 68.18
The buffer size is in bytes and the measured speed in MB/s. The copy
was performed repeatedly with given buffer and throughput averaged over
3 seconds.
Here we can see that the current kernel version has a higher entry cost
that shows up with small buffers. As buffer size grows both implementation
converge to the same throughput.
Now here's the exact same test performed on an XScale core (PXA255):
PTR alignment buffer size kernel version this version
------------------------------------------------------------
aligned 32 46.99 77.58
unaligned 32 53.61 59.59
aligned 100 107.19 136.59
unaligned 100 83.61 97.58
aligned 4096 129.13 129.98
unaligned 4096 128.36 128.53
aligned 1048576 53.76 59.41
unaligned 1048576 33.67 56.96
Again we can see the entry setup cost being higher for the current kernel
before getting to the main copy loop. Then throughput results converge
as long as the buffer remains in the cache. Then the 1MB case shows more
differences probably due to better pld placement and/or less instruction
interlocks in this proposed implementation.
Disclaimer: The PXA system was running with slower clocks than the
StrongARM system so trying to infer any conclusion by comparing those
separate sets of results side by side would be completely inappropriate.
So... What this patch does is to replace both memcpy and memmove with
an implementation based on the provided copy code template. The memmove
code is kept separate since it is used only if the memory areas involved
do overlap in which case the code is a transposition of the template but
with the copy occurring in the opposite direction (trying to fit that
mode into the template turned it into a mess not worth it for memmove
alone). And obviously both memcpy and memmove were tested with all kinds
of pointer alignments and buffer sizes to exercise all code paths for
correctness.
The next patch will provide the now trivial replacement implementation
copy_to_user and copy_from_user.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Required for future enhancement patches.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Lubbock updates:
* Provide an address for the SMC91x chip that doesn't generate
a boot-time warning (matching the EEPROM).
* Update MMC support to (a) detect card insert/remove, and
(b) report the readonly switch setting for SD cards.
Previously, MMC/SD cards had to be present at boot time else they
couldn't be detected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform data for the LCD/framebuffer driver for
the RX3715 LCD panel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Switch the users of ixp2000_reg_write that depend on writes being
flushed out of the write buffer by the time that function returns
over to ixp2000_reg_wrb.
When using XCB=101, writes to the same functional unit are still
guaranteed to complete in order, so we only need to protect against:
- reordering of writes to different functional units
- masking an interrupt and then reenabling the IRQ bit in CPSR
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The enp2611 version of the ixp2000 netdev driver needs to be able to
access a number of on-board peripherals. ioremap() is not suitable
for this, as that will cause XCB=000 mappings to be done, which will
make the cpu susceptible to crashing on ixp2400 erratum #66. Properly
aligned iotable mappings with MT_IXP2000_DEVICE will cause section
mappings with XCB=101 to be done, which is safe.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A recent commit that removed rtas-fw.h and moved its contents to
include/asm-powerpc/rtas.h forgot to also remove the inclusion of
it in arch/powerpc/platforms/pseries/setup.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a revised version. This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch). In fact it is used in the powermac interrupt code
(but not on pSeries).
- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S
- ppc32 previously used a full "sync" barrier at the end of
test_and_*_bit(), whereas ppc64 used an "isync". The merged version
uses "isync", since I believe that's sufficient.
- The ppc64 versions of then minix_*() bitmap functions have changed
semantics. Previously on ppc64, these functions were big-endian
(that is bit 0 was the LSB in the first 64-bit, big-endian word).
On ppc32 (and x86, for that matter, they were little-endian. As far
as I can tell, the big-endian usage was simply wrong - I guess
no-one ever tried to use minixfs on ppc64.
- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
inline (they were already out-of-line on ppc64).
- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
the merged bitops. What it was doing in mmu_context.h in the first
place, I have no idea.
- The fls() function is now implemented using the cntlzw instruction
on ppc64, instead of generic_fls(), as it already was on ppc32.
- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
arch/ppc/Makefile. This in turn requires some changes to
arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.
Built and running on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch simply moves files over to arch/powerpc without making
any changes to them.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The nvram code formally known as bpa_nvram.c is rather
generic really, so it is quite likely to be useful to
future boards not based on cell.
This patch puts it into arch/powerpc/sysdev.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cell uses the same code as pSeries for flashing the firmware
through rtas, so the implementation should not be part of
platforms/pseries.
Put it into arch/powerpc/kernel instead.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During the conversion to the merge tree, the Cell specific
SMP initialization was removed from the pSeries code.
This creates a new Cell specific SMP implementation file.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The official name for BPA is now CBEA (Cell Broadband
Engine Architecture). This patch renames all occurences
of the term BPA to 'Cell' for easier recognition.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
By parsing the command line earlier, we can add the mem= value to the
flattened device tree and let the generic code sort out the memory limit
for us.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Change USER/KERNEL_DS so that the merged version of
__strnlen_user can be used which allows us to complete the
removal of arch/ppc64/lib/.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Commit f2b36db692 causes a bootup hang on
at least one machine. Revert for now until we understand why. The old
code may be ugly, but it works.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split. Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line. This puts the declaration
in system.h and the definition in mem.c. This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reads from an HPET register require a round trip to the south bridge and are
almost as slow as PCI reads. By caching the last value we've written to the
comparator register, we can eliminate all HPET reads from the fast path in the
emulated RTC interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure that the RTC timer is in non-periodic mode; some stupid BIOS might
have initialized it to periodic mode.
Furthermore, don't set the SETVAL bit in the config register. This wouldn't
have any effect unless the timer was in period mode (which it isn't), and then
the actual timer frequency would be half that of the desired one because
incrementing the comparator in the interrupt handler would be done after the
hardware has already incremented it itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the emulated RTC interrupt is no longer needed, we better disable it;
otherwise, we get a spurious interrupt whenever the timer has rolled over and
reaches the same comparator value.
Having a superfluous interrupt every five minutes doesn't hurt much, but it's
bad style anyway. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the remaining "Using plain integer as NULL pointer" sparse
warnings to use NULL. (Not duplicating patches that are already in -mm,
-bird, or -kj.)
Convert isdn driver struct initializer to use C99 syntax.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This ioctl doesn't exist for native i386.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the pid argument a long as on every other arcihtecture. Despite pid_t
beeing a 32bit type even on 64bit parisc this is not an ABI change due to
the parisc calling conventions. And even if it did it wouldn't matter too
much because 64bit userspace on parisc is in an embrionic stage.
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
task_struct is an internal structure to the kernel with a lot of good
information, that is probably interesting in core dumps. However there is
no way for user space to know what format that information is in making it
useless.
I grepped the GDB 6.3 source code and NT_TASKSTRUCT while defined is not
used anywhere else. So I would be surprised if anyone notices it is
missing.
In addition exporting kernel pointers to all the interesting kernel data
structures sounds like the very definition of an information leak. I
haven't a clue what someone with evil intentions could do with that
information, but in any attack against the kernel it looks like this is the
perfect tool for aiming that attack.
So since NT_TASKSTRUCT is useless as currently defined and is potentially
dangerous, let's just not export it.
(akpm: Daniel Jacobowitz <dan@debian.org> "would be amazed" if anything was
using NT_TASKSTRUCT).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove timer_list.magic and associated debugging code.
I originally added this when a spinlock was added to timer_list - this meant
that an all-zeroes timer became illegal and init_timer() was required.
That spinlock isn't even there any more, although timer.base must now be
initialised.
I'll keep this debugging code in -mm.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
TIOCSTART and TIOCSTOP are defined in asm/ioctls.h and asm/termios.h by
various architectures but not actually implemented anywhere but in the IRIX
compatibility layer, so remove their COMPATIBLE_IOCTL from parisc, ppc64
and sparc64.
Move the TIOCSLTC COMPATIBLE_IOCTL to common code, guided by an ifdef to
only show up on architectures that support it (same as the code handling it
in tty_ioctl.c), aswell as it's brother TIOCGLTC that wasn't handled so
far.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every user of init_timer() also needs to initialize ->function and ->data
fields. This patch adds a simple setup_timer() helper for that.
The schedule_timeout() is patched as an example of usage.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix fullscreen view of the 3270 device driver.
Signed-off-by: Richard Hitt <rbh00@utsglobal.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I just noted that -mtune is used, which is only supported on recent GCCs; by
reading http://gcc.gnu.org/gcc-3.4/changes.html, you see "-mcpu has been
renamed to -mtune.", so for GCC < 3.4 we're not using any specific tuning in
the appropriate cases. However -mcpu is deprecated, so use -mtune when
possible.
This was introduced by commit e9d4dce954a60dc23dd1d967766ca2347b780e54 of the
old tree (between 2.6.10-rc3 and 2.6.10) by Linus Torvalds, to remove the use
of -march, since that could trigger gcc using SSE on its own. But no
attention was used about using -mcpu vs. -mtune.
And btw, the old 2.6.4 code (for instance) was:
cflags-$(CONFIG_MPENTIUMII) += $(call check_gcc,-march=pentium2,-march=i686)
cflags-$(CONFIG_MPENTIUMIII) += $(call check_gcc,-march=pentium3,-march=i686)
cflags-$(CONFIG_MPENTIUMM) += $(call check_gcc,-march=pentium3,-march=i686)
cflags-$(CONFIG_MPENTIUM4) += $(call check_gcc,-march=pentium4,-march=i686)
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was used in the old dark age of 2.4, ARCH_CFLAGS doesn't work any more
since some time, and UM_FASTCALL was never used in 2.6.
Instead, reintroduce the thing more properly now, directly in
include/asm-um/linkage.h.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove RWSEM_GENERIC_SPINLOCK, it's now defined (only if needed) by the
underlying arch/i386/Kconfig.cpu. Leave it only for x86_64. Even there, it's
totally wrong, as they even have the code to support XCHG_ADD.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make UML share the underlying cpu-specific tuning done on i386.
Actually, for now many config options aren't used a lot - but that can be done
later. Also, UML relies on GCC optimization for things like memcpy and such
more than i386, so specifying the correct -march and -mtune should be enough.
Later, we may want to correct some other stuff.
For instance, since FPU context switching, for us, is done (at least
partially, i.e. between our kernelspace and userspace) by the host, we may
allow usage of FPU operations by GCC. This doesn't hold for kernelspace vs.
kernelspace, but we don't support preemption.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update SMC91x driver for m32r.
- Remove needless NONCACHE_OFFSET adjustment.
> [PATCH 2.6.14-rc4] m32r: NONCACHE_OFFSET in _port2addr
> Change _port2addr() not to add NONCACHE_OFFSET.
> Adding NONCACHE_OFFSET requires needless address adjusting by a driver
> using ioremap() like a SMC91x driver.
- Fix lots of warnings as following:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c: In function `smc_reset':
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:324: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:325: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:341: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:342: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change _port2addr() not to add NONCACHE_OFFSET. Adding NONCACHE_OFFSET
requires needless address adjusting by a driver using ioremap() like a
SMC91x driver.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp use the PG_nosave and PG_nosave_free flags to
mark pages that should be freed in case of an error during resume.
This allows us to simplify the code and to use swsusp_free() in all of the
swsusp's resume error paths, which makes them actually work.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpu cache entries should be populated only when cpu is online and removed
when they are logically offlined.
Without which entries are not removed when cpu is offlined, or dont appear
when we boot with maxcpus=1 and then kick the rest of the cpus via echo 1
to the sysfs online file.
- Changed __devinit to __cpuinit for consistency.
- Changed sysfs_driver_register to register_cpu_notifier.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a check for the return value of acpi_find_root_pointer().
Without this patch systems without ACPI support such as QEMU crashes when
booting a NUMA kernel with CONFIG_ACPI_SRAT=y.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After staring at mpparse.c for a little longer I noticed that when we hit
our limit of num_processors we are filtering out information about other
processors that we can still store.
This patch just reorders the code so we store everything we can.
This should avoid the incorrect warning about our boot CPU not being listed
by the BIOS that we are now getting in the kexec on panic case, and it
should allow us to detect all apicid conflicts even when our physical
number of cpus exceeds maxcpus.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Removes the unnecessary call to local_irq_disable().
o Kdump was failing while second kernel was coming up. Check for presence
of boot cpu apic id was failing in (apic_id_registered), hence hitting
BUG().
o This should not have failed because before calling setup_local_APIC(), it is
ensured that even if BIOS has not reported boot cpu, then hard set the
prence of it. Problem happens because of usage of hard_smp_processor_id()
which is hardcoded to zero in case of non SMP kernel. In kdump case second
kernel can boot on a cpu whose boot cpu id is not zero.
o Using boot_cpu_physical_apicid instead to hard set the presence of boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle 32-bit mtrr ioctls in the mtrr driver instead of the ia32
compatability layer.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If VMX feature is available in the CPU, this patch will make it visible in
the /proc/cpuinfo with the cpuid detection.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is dangerous to shutdown the apics in machine_crash_shutdown.
With my previous patch to initialize apics in init_IRQ we should be able to
boot a kernel without this. As long as we reinitialize the APICs we don't
care what state they were in during bootup.
This should make machine_crash_shutdown noticeably more reliable.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kinds of ugliness exists because we don't initialize
the apics during init_IRQs.
- We calibrate jiffies in non apic mode even when we are using apics.
- We have to have special code to initialize the apics when non-smp.
- The legacy i8259 must exist and be setup correctly, even
when we won't use it past initialization.
- The kexec on panic code must restore the state of the io_apics.
- init/main.c needs a special case for !smp smp_init on x86
In addition to pure code movement I needed a couple
of non-obvious changes:
- Move setup_boot_APIC_clock into APIC_late_time_init for
simplicity.
- Use cpu_khz to generate a better approximation of loops_per_jiffies
so I can verify the timer interrupt is working.
- Call setup_apic_nmi_watchdog again after cpu_khz is initialized on
the boot cpu.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The per cpu nmi watchdog timer is based on an event counter. idle cpus
don't generate events so the NMI watchdog doesn't fire and the test to see
if the watchdog is working fails.
- Add nmi_cpu_busy so idle cpus don't mess up the test.
- kmalloc prev_nmi_count to keep kernel stack usage bounded.
- Improve the error message on failure so there is enough
information to debug problems.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to restore virtual wire mode on reboot, which only
works if we can figure out where the i8259 is connected. This is very
useful when we kexec another kernel and likely helpful when dealing with a
BIOS that make assumptions about how the system is setup.
Since the acpi MADT table does not provide the location where the i8259 is
connected we have to look at the hardware to figure it out.
Most systems have the i8259 connected the local apic of the cpu so won't be
affected but people running Opteron and some serverworks chipsets should be
able to use kexec now.
In addition this patch removes the hard coded assumption that the io_apic
that delivers isa interrups is always known to the kernel as io_apic 0. As
there does not appear to be anything to guarantee that assumption is true.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is platform code update for ES7000: disables IRQ overrides for the
recent ES7000 (Rascal/Zorro), cleans up the compile warning. The patch
only affects the ES7000 subarch.
Signed-off-by: <Natalie.Protasevich@unisys.com>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that prints the cache size assumes that L3 always lives in chipset
and is shared across CPUs. Which is not really true.
I think all the cachesizes reported by cpuid are in the processor itself.
The attached patch changes the code to reflect that.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was reported because someone was getting oopses reading /proc/iomem.
It was tracked down to a zero-sized 'struct resource' entry which was
located right at 4GB.
You need two conditions to hit this bug: a BIOS E820_RAM area starting at
exactly the boundary where you specify mem= (to get a zero-sized entry),
and for the legacy_init_iomem_resources() loop to skip that resource (which
only happens at exactly 4G).
I think the killing zero-sized e820 entry is the easiest way to fix this.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make P6 MCA initialization code complaint with guidelines in IA-32 SDM
Vol3. Bank 0 control register should not be set by OS and clear status
registers on all banks on reset.
This will prevent false MCE alarms on the systems that has some non-MCE
information left-over in MC0_STATUS on reboot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an accessor function for getting the per-CPU gdt. Callee must already
have the CPU.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The per-CPU initialization code is copying in bogus data into
thread->tls_array. Note that it copies &per_cpu(cpu_gdt_table, cpu), not
&per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TLS_MIN). That is totally broken
and unnecessary. Make the initialization explicitly NULL.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch allows physical bring-up of new processors (not initially present
in the configuration) from facilities such as driver/utility implemented on
a platform. The actual method of making processors available is up to the
platform implementation.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial internal version of Venki's cpuid(4) deterministic cache parameter
identification patch used static arrays of size MAX_CACHE_LEAVES. Final patch
which made to the base used dynamic array allocation, with this
MAX_CACHE_LEAVES limit hunk still in place.
cpuid(4) already has a mechanism to find out the number of cache levels
implemented and there is no need for this hardcoded MAX_CACHE_LEAVES limit.
So remove the MAX_CACHE_LEAVES limit from the routine which calculates the
number of cache levels using cpuid(4)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There exists a field io_bitmap_owner in the TSS that is only checked, but
never set to anything else but NULL.
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mxcsr_feature_mask_init isn't needed in suspend/resume time (we can use
boot time mask). And actually it's harmful, as it clear task's saved
fxsave in resume. This bug is widely seen by users using zsh.
(akpm: my eyes. Fixed some surrounding whitespace mess)
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adjusts i386's cmpxchg patterns so that
- for word and long cmpxchg-es the compiler can utilize all possible
registers
- cmpxchg8b gets disabled when the minimum specified hardware architectur
doesn't support it (like was already happening for the byte, word, and
long ones).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I just found out that some precision is unnecessarily lost in the
arch/i386/kernel/timers/timer_tsc.c:set_cyc2ns_scale function. It uses a
cpu_mhz parameter when it could use a cpu_khz. In the specific case of an
Intel P4 running at 3001.171 Mhz, the truncation to 3001 Mhz leads to an
imprecision of 19 microseconds per second : this is very sad for a timer with
nearly nanosecond accuracy.
Fix the x86_64 architecture too.
Cc: george anzinger <george@mvista.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
