Add kernel-doc to skbuff.h, skbuff.c to eliminate kernel-doc warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a bug which was reported and diagnosed by
Stefan Jones <stefan.jones@churchillrandoms.co.uk>
IDR trees include a cache of idr_layer objects. There's no way to destroy
this cache, so when we discard an overall idr tree we end up leaking some
memory.
Add and use idr_destroy() for this. v9fs and infiniband also need to use
idr_destroy() to avoid leaks.
Or, we make the cache global, like radix_tree_preload(). Which is probably
better. Later.
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This reverts commit 3359b54c8c and
replaces it with a cleaner version that is purely based on page table
operations, so that the synchronization between inode size and hugetlb
mappings becomes moot.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.
We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.
The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator. But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages(). We may be done that post 2.6.14 as a
cleanup.
With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hugetlb pages are currently pre-faulted. At the time of mmap of
hugepages, we populate the new PTEs. It is possible that HW has already
cached some of the unused PTEs internally. These stale entries never
get a chance to be purged in existing control flow.
This patch extends the check in page fault code for hugepages. Check if
a faulted address falls with in size for the hugetlb file backing it.
We return VM_FAULT_MINOR for these cases (assuming that the arch
specific page-faulting code purges the stale entry for the archs that
need it).
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
[ This is apparently arguably an ia64 port bug. But the code won't
hurt, and for now it fixes a real problem on some ia64 machines ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not only are the qop parameters that are passed around throughout the gssapi
unused by any currently implemented mechanism, but there appears to be some
doubt as to whether they will ever be used. Let's just kill them off for now.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add support for privacy to the krb5 rpcsec_gss mechanism.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The code this was originally derived from processed wrap and mic tokens using
the same functions. This required some contortions, and more would be required
with the addition of xdr_buf's, so it's better to separate out the two code
paths.
In preparation for adding privacy support, remove the last vestiges of the
old wrap token code.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Various xdr encode routines use au_rslack to guess where the reply argument
will end up, so we can set up the xdr_buf to recieve data into the right place
for zero copy.
Currently we calculate the au_rslack estimate when we check the verifier.
Normally this only depends on the verifier size. In the integrity case we add
a few bytes to allow for a length and sequence number.
It's a bit simpler to calculate only the verifier size when we check the
verifier, and delay the full calculation till we unwrap.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For privacy, we need to allocate pages to store the encrypted data (passed
in pages can't be used without the risk of corrupting data in the page cache).
So we need a way to free that memory after the request has been transmitted.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add support for privacy to generic gss-api code. This is dead code until we
have both a mechanism that supports privacy and code in the client or server
that uses it.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Make NFSv4 return the fully initialized file pointer with the
stateid that it created in the lookup w/intent.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is needed by NFSv4 for atomicity reasons: our open command is in
fact a lookup+open, so we need to be able to propagate open context
information from lookup() into the resulting struct file's
private_data field.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Once the state_owner and lock_owner semaphores get removed, it will be
possible for other OPEN requests to reopen the same file if they have
lower sequence ids than our CLOSE call.
This patch ensures that we recheck the file state once
nfs_wait_on_sequence() has completed waiting.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFSv4 file state-changing functions such as OPEN, CLOSE, LOCK,... are all
labelled with "sequence identifiers" in order to prevent the server from
reordering RPC requests, as this could cause its file state to
become out of sync with the client.
Currently the NFS client code enforces this ordering locally using
semaphores to restrict access to structures until the RPC call is done.
This, of course, only works with synchronous RPC calls, since the
user process must first grab the semaphore.
By dropping semaphores, and instead teaching the RPC engine to hold
the RPC calls until they are ready to be sent, we can extend this
process to work nicely with asynchronous RPC calls too.
This patch adds a new list called "rpc_sequence" that defines the order
of the RPC calls to be sent. We add one such list for each state_owner.
When an RPC call is ready to be sent, it checks if it is top of the
rpc_sequence list. If so, it proceeds. If not, it goes back to sleep,
and loops until it hits top of the list.
Once the RPC call has completed, it can then bump the sequence id counter,
and remove itself from the rpc_sequence list, and then wake up the next
sleeper.
Note that the state_owner sequence ids and lock_owner sequence ids are
all indexed to the same rpc_sequence list, so OPEN, LOCK,... requests
are all ordered w.r.t. each other.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, call_encode will cause the entire RPC call to abort if it returns
an error. This is unnecessarily rigid, and gets in the way of attempts
to allow the NFSv4 layer to order RPC calls that carry sequence ids.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
lock_kiocb() was introduced to serialize retrying and cancellation. In the
process of doing so it tried to sleep waiting for KIF_LOCKED while holding
the ctx_lock spinlock. Recent fixes have ensured that multiple concurrent
retries won't be attempted for a given iocb. Cancel has other problems and
has no significant in-tree users that have been complaining about it. So
for the immediate future we'll revert sleeping with the lock held and will
address proper cancellation and retry serialization in the future.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes call_rcu() keep track of how many events there are on the RCU
list, and cause a reschedule event when the list gets too long.
This helps keep RCU event lists down.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that all the list_*_rcu primitives are missing a memory barrier
on the very first dereference. For example,
#define list_for_each_rcu(pos, head) \
for (pos = (head)->next; prefetch(pos->next), pos != (head); \
pos = rcu_dereference(pos->next))
It will go something like:
pos = (head)->next
prefetch(pos->next)
pos != (head)
do stuff
We're missing a barrier here.
pos = rcu_dereference(pos->next)
fetch pos->next
barrier given by rcu_dereference(pos->next)
store pos
Without the missing barrier, the pos->next value may turn out to be stale.
In fact, if "do stuff" were also dereferencing pos and relying on
list_for_each_rcu to provide the barrier then it may also break.
So here is a patch to make sure that we have a barrier for the first
element in the list.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... otherwise, things like alpha and sparc64 break and break
badly. They define cpu_possible_map to something else in smp.h
*AFTER* having included cpumask.h.
If that puppy is a macro, expansion will happen at the actual
caller, when we'd already seen #define cpu_possible_map ... and we will
get the right thing used.
As an inline helper it will be tokenized before we get to that
define and that's it; no matter what we define later, it won't affect
anything. We get modules with dependency on cpu_possible_map instead
of the right symbol (phys_cpu_present_map in case of sparc64), or outright
link errors if they are built-in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix copy and paste error in jiffies_to_AHZ conversion which leads to wrong
BSD accounting information on alpha and ia64 when
CONFIG_BSD_PROCESS_ACCT_V3 is turned on.
Also update comment to match reorganised header files.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch by Harald Welte, with feedback from Herbert Xu
and testing by Sbastien Bernard.
EBTABLES, ARP tables, and IP/IP6 tables all assume that cpus
are numbered linearly. That is not necessarily true.
This patch fixes that up by calculating the largest possible
cpu number, and allocating enough per-cpu structure space given
that.
Signed-off-by: David S. Miller <davem@davemloft.net>
When netpoll is not being used, the macro that
defines the removed routing netpoll_poll_lock
defines the return as zero, but the real
routine returns a `void *`
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability of changing the state a TCP connection. I know
that this must be used with care but it's required to provide a complete
conntrack creation via conntrack_netlink. So I'll document this aspect on
the upcoming docs.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially we used 64bit counters for conntrack-based accounting, since we
had no event mechanism to tell userspace that our counters are about to
overflow. With nfnetlink_conntrack, we now have such a event mechanism and
thus can save 16bytes per connection.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep consistency, the TCP private protocol information is nested
attributes under CTA_PROTOINFO_TCP. This way the sequence of attributes to
access the TCP state information looks like here below:
CTA_PROTOINFO
CTA_PROTOINFO_TCP
CTA_PROTOINFO_TCP_STATE
instead of:
CTA_PROTOINFO
CTA_PROTOINFO_TCP_STATE
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this #include, __be16 is not defined and userspace programs
will break.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 'rustynat' was merged in 2.6.12, the use of the "helper" pointer of
struct ipt_nat_info was obsoleted, but the pointer not removed from the
struct.
This patch removes the pointer, thereby yet again shrinking struct
ip_conntrack.
Discovered-by: Rusty Russell <rusty@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Henrik Nordstrom pointed out, all our efforts with "split endian" (i.e.
host byte order tags, net byte order values) are useless, unless a parser
can determine whether an attribute is nested or not.
This patch steals the highest bit of nfattr.nfa_type to indicate whether
the data payload contains a nested nfattr (1) or not (0).
This will break userspace compatibility, but luckily no kernel with
nfnetlink was released so far.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a process issues an URB from userspace and (starts to) terminate
before the URB comes back, we run into the issue described above. This
is because the urb saves a pointer to "current" when it is posted to the
device, but there's no guarantee that this pointer is still valid
afterwards.
In fact, there are three separate issues:
1) the pointer to "current" can become invalid, since the task could be
completely gone when the URB completion comes back from the device.
2) Even if the saved task pointer is still pointing to a valid task_struct,
task_struct->sighand could have gone meanwhile.
3) Even if the process is perfectly fine, permissions may have changed,
and we can no longer send it a signal.
So what we do instead, is to save the PID and uid's of the process, and
introduce a new kill_proc_info_as_uid() function.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
[ Fixed up types and added symbol exports ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp avoid the possible temporary corruption
of page translation tables during resume on x86-64. This is achieved by
creating a copy of the relevant page tables that will not be modified by
swsusp and can be safely used by it on resume.
The problem is that during resume on x86-64 swsusp may temporarily
corrupt the page tables used for the direct mapping of RAM. If that
happens, a page fault occurs and cannot be handled properly, which leads
to the solid hang of the affected system. This leads to the loss of the
system's state from before suspend and may result in the loss of data or
the corruption of filesystems, so it is a serious issue. Also, it
appears to happen quite often (for me, as often as 50% of the time).
The problem is related to the fact that (at least) one of the PMD
entries used in the direct memory mapping (starting at PAGE_OFFSET)
points to a page table the physical address of which is much greater
than the physical address of the PMD entry itself. Moreover,
unfortunately, the physical address of the page table before suspend
(i.e. the one stored in the suspend image) happens to be different to
the physical address of the corresponding page table used during resume
(i.e. the one that is valid right before swsusp_arch_resume() in
arch/x86_64/kernel/suspend_asm.S is executed). Thus while the image is
restored, the "offending" PMD entry gets overwritten, so it does not
point to the right physical address any more (i.e. there's no page
table at the address pointed to by it, because it points to the address
the page table has been at during suspend). Consequently, if the PMD
entry is used later on, and it _is_ used in the process of copying the
image pages, a page fault occurs, but it cannot be handled in the normal
way and the system hangs.
In principle we can call create_resume_mapping() from
swsusp_arch_resume() (ie. from suspend_asm.S), but then the memory
allocations in create_resume_mapping(), resume_pud_mapping(), and
resume_pmd_mapping() must be made carefully so that we use _only_
NosaveFree pages in them (the other pages are overwritten by the loop in
swsusp_arch_resume()). Additionally, we are in atomic context at that
time, so we cannot use GFP_KERNEL. Moreover, if one of the allocations
fails, we should free all of the allocated pages, so we need to trace
them somehow.
All of this is done in the appended patch, except that the functions
populating the page tables are located in arch/x86_64/kernel/suspend.c
rather than in init.c. It may be done in a more elegan way in the
future, with the help of some swsusp patches that are in the works now.
[AK: move some externs into headers, renamed a function]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch splits key permissions checking out of key-ui.h and
moves it into a .c file. It's quite large and called quite a lot, and
it's about to get bigger with the addition of LSM support for keys...
key_any_permission() is also discarded as it's no longer used.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix nocast sparse warnings:
include/linux/textsearch.h:165:57: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix implicit nocast warnings in connector code:
drivers/connector/connector.c:102:24: warning: implicit cast to nocast type
drivers/connector/connector.c:114:45: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix implicit nocast warnings in atm code:
net/atm/atm_misc.c:35:44: warning: implicit cast to nocast type
drivers/atm/fore200e.c:183:33: warning: implicit cast to nocast type
Also use kzalloc() instead of kmalloc().
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnaldo and I agreed it could be applied now, because I have other
pending patches depending on this one (Thank you Arnaldo)
(The other important patch moves skc_refcnt in a separate cache line,
so that the SMP/NUMA performance doesnt suffer from cache line ping pongs)
1) First some performance data :
--------------------------------
tcp_v4_rcv() wastes a *lot* of time in __inet_lookup_established()
The most time critical code is :
sk_for_each(sk, node, &head->chain) {
if (INET_MATCH(sk, acookie, saddr, daddr, ports, dif))
goto hit; /* You sunk my battleship! */
}
The sk_for_each() does use prefetch() hints but only the begining of
"struct sock" is prefetched.
As INET_MATCH first comparison uses inet_sk(__sk)->daddr, wich is far
away from the begining of "struct sock", it has to bring into CPU
cache cold cache line. Each iteration has to use at least 2 cache
lines.
This can be problematic if some chains are very long.
2) The goal
-----------
The idea I had is to change things so that INET_MATCH() may return
FALSE in 99% of cases only using the data already in the CPU cache,
using one cache line per iteration.
3) Description of the patch
---------------------------
Adds a new 'unsigned int skc_hash' field in 'struct sock_common',
filling a 32 bits hole on 64 bits platform.
struct sock_common {
unsigned short skc_family;
volatile unsigned char skc_state;
unsigned char skc_reuse;
int skc_bound_dev_if;
struct hlist_node skc_node;
struct hlist_node skc_bind_node;
atomic_t skc_refcnt;
+ unsigned int skc_hash;
struct proto *skc_prot;
};
Store in this 32 bits field the full hash, not masked by (ehash_size -
1) Using this full hash as the first comparison done in INET_MATCH
permits us immediatly skip the element without touching a second cache
line in case of a miss.
Suppress the sk_hashent/tw_hashent fields since skc_hash (aliased to
sk_hash and tw_hash) already contains the slot number if we mask with
(ehash_size - 1)
File include/net/inet_hashtables.h
64 bits platforms :
#define INET_MATCH(__sk, __hash, __cookie, __saddr, __daddr, __ports, __dif)\
(((__sk)->sk_hash == (__hash))
((*((__u64 *)&(inet_sk(__sk)->daddr)))== (__cookie)) && \
((*((__u32 *)&(inet_sk(__sk)->dport))) == (__ports)) && \
(!((__sk)->sk_bound_dev_if) || ((__sk)->sk_bound_dev_if == (__dif))))
32bits platforms:
#define TCP_IPV4_MATCH(__sk, __hash, __cookie, __saddr, __daddr, __ports, __dif)\
(((__sk)->sk_hash == (__hash)) && \
(inet_sk(__sk)->daddr == (__saddr)) && \
(inet_sk(__sk)->rcv_saddr == (__daddr)) && \
(!((__sk)->sk_bound_dev_if) || ((__sk)->sk_bound_dev_if == (__dif))))
- Adds a prefetch(head->chain.first) in
__inet_lookup_established()/__tcp_v4_check_established() and
__inet6_lookup_established()/__tcp_v6_check_established() and
__dccp_v4_check_established() to bring into cache the first element of the
list, before the {read|write}_lock(&head->lock);
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've found the problem in general. It affects any 64-bit
architecture. The problem occurs when you change the system time.
Suppose that when you boot your system clock is forward by a day.
This gets recorded down in skb_tv_base. You then wind the clock back
by a day. From that point onwards the offset will be negative which
essentially overflows the 32-bit variables they're stored in.
In fact, why don't we just store the real time stamp in those 32-bit
variables? After all, we're not going to overflow for quite a while
yet.
When we do overflow, we'll need a better solution of course.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use '#ifdef' consistently on __KERNEL__. This was reported as bug #5340
(isn't easier to send a fix than report the bug?!)
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only one of the run or kick path is supposed to put an iocb on the run
list. If both of them do it than one of them can end up referencing a
freed iocb. The kick path could delete the task_list item from the wait
queue before getting the ctx_lock and putting the iocb on the run list.
The run path was testing the task_list item outside the lock so that it
could catch ki_retry methods that return -EIOCBRETRY *without* putting the
iocb on a wait queue and promising to call kick_iocb. This unlocked check
could then race with the kick path to cause both to try and put the iocb on
the run list.
The patch stops the run path from testing task_list by requring that any
ki_retry that returns -EIOCBRETRY *must* guarantee that kick_iocb() will be
called in the future. aio_p{read,write}, the only in-tree -EIOCBRETRY
users, are updated.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland points out that the flags end up having non-obvious dependencies
elsewhere, so revert aa55a08687 and add
some comments about why things are as they are.
We'll just have to fix up the broken comparisons. Roland has a patch.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_signal_stop:
for_each_thread(t) {
if (t->state < TASK_STOPPED)
++sig->group_stop_count;
}
However, TASK_NONINTERACTIVE > TASK_STOPPED, so this loop will not
count TASK_INTERRUPTIBLE | TASK_NONINTERACTIVE threads.
See also wait_task_stopped(), which checks ->state > TASK_STOPPED.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
[ We really probably should always use the appropriate bitmasks to test
task states, not do it like this. Using something like
#define TASK_RUNNABLE (TASK_RUNNING | TASK_INTERRUPTIBLE | \
TASK_UNINTERRUPTIBLE | TASK_NONINTERACTIVE)
and then doing "if (task->state & TASK_RUNNABLE)" or similar. But the
ordering of the task states is historical, and keeping the ordering
does make sense regardless. ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds extra permission grants to keys for the possessor of a
key in addition to the owner, group and other permissions bits. This makes
SUID binaries easier to support without going as far as labelling keys and key
targets using the LSM facilities.
This patch adds a second "pointer type" to key structures (struct key_ref *)
that can have the bottom bit of the address set to indicate the possession of
a key. This is propagated through searches from the keyring to the discovered
key. It has been made a separate type so that the compiler can spot attempts
to dereference a potentially incorrect pointer.
The "possession" attribute can't be attached to a key structure directly as
it's not an intrinsic property of a key.
Pointers to keys have been replaced with struct key_ref *'s wherever
possession information needs to be passed through.
This does assume that the bottom bit of the pointer will always be zero on
return from kmem_cache_alloc().
The key reference type has been made into a typedef so that at least it can be
located in the sources, even though it's basically a pointer to an undefined
type. I've also renamed the accessor functions to be more useful, and all
reference variables should now end in "_ref".
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following is generated when compiling a
recent (2.6.14-rc2-git5) kernel configured for
ARM, with GCC4.
CC init/main.o
In file included from include/linux/netdevice.h:29,
from include/net/sock.h:48,
from init/main.c:50:
include/linux/if_ether.h:114: error: array type has incomplete element type
It seems that if CONFIG_SYSCTL is not set, then
the compiler will throw an error due to the definition
of the ether_table[] array
Attached is a solution to the problem
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
Place them on separate cache lines in SMP to lower memory bouncing
between multiple CPU accessing the device.
- One part is mostly used on receive path (including
eth_type_trans()) (poll_list, poll, quota, weight, last_rx,
dev_addr, broadcast)
- One part is mostly used on queue transmit path (qdisc)
(queue_lock, qdisc, qdisc_sleeping, qdisc_list, tx_queue_len)
- One part is mostly used on xmit path (device)
(xmit_lock, xmit_lock_owner, priv, hard_start_xmit, trans_start)
'features' is placed outside of these hot points, in a location that
may be shared by all cpus (because mostly read)
name_hlist is moved close to name[IFNAMSIZ] to speedup __dev_get_by_name()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you've enabled conntrack and NAT as a module (standard case in all
distributions), and you've also enabled the new conntrack netlink
interface, loading ip_conntrack_netlink.ko will auto-load iptable_nat.ko.
This causes a huge performance penalty, since for every packet you iterate
the nat code, even if you don't want it.
This patch splits iptable_nat.ko into the NAT core (ip_nat.ko) and the
iptables frontend (iptable_nat.ko). Threfore, ip_conntrack_netlink.ko will
only pull ip_nat.ko, but not the frontend. ip_nat.ko will "only" allocate
some resources, but not affect runtime performance.
This separation is also a nice step in anticipation of new packet filters
(nf-hipac, ipset, pkttables) being able to use the NAT core.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If input message rate from userspace is too high, do not drop them,
but try to deliver using work queue allocation.
Failing there is some kind of congestion control.
It also removes warn_on on this condition, which scares people.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added a missing TO_NATIVE call to scripts/mod/file2alias.c:do_pcmcia_entry()
- Add an alignment attribute to struct pcmcia_device_no to solve an alignment
issue seen when cross-compiling on x86 for m68k.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
