We used to access the 64-bit IRQ IMAP and ICLR registers of bus
controllers 4-bytes in and as a 32-bit register word, since only the
low 32-bits were relevant. This seemed like a good idea at the time.
But the PCI-E controller requires full 8-byte 64-bit access to
these registers, so we switched over to accessing them fully.
SBUS was not adjusted properly, which broke interrupts completely.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are on hummingbird, bus runs at 66MHZ.
pbm->pci_bus should be setup with the result of pci_scan_one_pbm()
or else we deref NULL pointers in the error interrupt handlers.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not just sun4v hypervisor platforms that should return true
for this, sun4u with UltraSPARC-IV should return true too.
Signed-off-by: David S. Miller <davem@davemloft.net>
The scheduling domain hierarchy is:
all cpus -->
cpus that share an instruction cache -->
cpus that share an integer execution unit
Signed-off-by: David S. Miller <davem@davemloft.net>
If the system supports hypervisor based statistics, allow them to
be fetched, enabled, and disabled via sysfs.
Enable and disable via the boolean:
/sys/devices/systems/cpu/cpuN/mmustat_enable
Statistic values are provided under:
/sys/devices/systems/cpu/cpuN/mmu_status/
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, use per-cpu data for struct cpu. Calling kmalloc for
each cpu in topology_init() is just plain clumsy.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RO_DATA section were hardcoded to a specific
alignment in include/asm-generic/vmlinux.h.
But for sparc64 this did not match the PAGE_SIZE.
Introduce a new section definition named:
RO_DATA that takes actual alignment as parameter.
RODATA are provided for backward compatibility.
On top of this avoid hardcoding alignment for
sparc64 in reset of the script
Fix is build-tested on sparc64 + x86_64.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Several interfaces were missing and others misnumbered or
improperly documented.
Also, make sure to check the return value when registering
the kernel TSBs with the hypervisor. This helped to find
the 4MB kernel TSB alignment bug fixed in a previous changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) The TSB lookup was not using the correct hash mask.
2) It was not aligned on a boundary equal to it's size,
which is required by the sun4v Hypervisor.
wasn't having it's return value checked, and that bug will be fixed up
as well in a subsequent changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
It was using an immediate _PAGE_EXEC_4U value in an 'and'
instruction to perform the test. This doesn't work because
the immediate field is signed 13-bit, this the mask being
tested against the PTE was 0x1000 sign-extended to 32-bits
instead of just plain 0x1000.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is bug 8540 on bugzilla.kernel.org
arch/sparc64/time.c contains references to assorted bq4802 stuff if
CONFIG_PCI is not set, and compile fails. I #ifdef'ed out everything
that looks PCI-ish in that file.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cheetah systems can have cpuids as large as 1023, although physical
systems don't have that many cpus.
Only three limitations existed in the kernel preventing arbitrary
NR_CPUS values:
1) dcache dirty cpu state stored in page->flags on
D-cache aliasing platforms. With some build time
calculations and some build-time BUG checks on
page->flags layout, this one was easily solved.
2) The cheetah XCALL delivery code could only handle
a cpumask with up to 32 cpus set. Some simple looping
logic clears that up too.
3) thread_info->cpu was a u8, easily changed to a u16.
There are a few spots in the kernel that still put NR_CPUS
sized arrays on the kernel stack, but that's not a sparc64
specific problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages were very useful when bringing up the
OBP based PCI device scan code, but it's just a lot
of noise every bootup now especially on big machines.
The messages can be re-enabled via 'ofpci_debug=1' on
the kernel command line.
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle arbitrary base and length values as long as they
are multiples of IO_PAGE_SIZE.
Bug found by Arun Kumar Rao.
Signed-off-by: David S. Miller <davem@davemloft.net>
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably. So add a small set of interfaces
to request API versions and query current settings.
This allows us to fix some bugs in the hypervisor console:
1) If we can negotiate API group CORE of at least major 1
minor 1 we can use con_read and con_write which can improve
console performance quite a bit.
2) When we do a console write request, we should hold the
spinlock around the whole request, not a byte at a time.
What would happen is that it's easy for output from
different cpus to get mixed with each other.
3) Use consistent udelay() based polling, udelay(1) each
loop with a limit of 1000 polls to handle stuck hypervisor
console.
Signed-off-by: David S. Miller <davem@davemloft.net>
When auditing syscalls that send signals, log the pid and security
context for each target process. Optimize the data collection by
adding a counter for signal-related rules, and avoiding allocating an
aux struct unless we have more than one target process. For process
groups, collect pid/context data in blocks of 16. Move the
audit_signal_info() hook up in check_kill_permission() so we audit
attempts where permission is denied.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Use alloc_pci_dev() in PCI bus probes.
[SPARC64]: Bump PROMINTR_MAX to 32.
[SPARC64]: Fix recursion in PROM tree building.
[SERIAL] sunzilog: Interrupt enable before ISR handler installed
[SPARC64] PCI: Consolidate PCI access code into pci_common.c
Use iteration for scanning of PROM node siblings.
Based upon a patch by Greg Onufer, who found this bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the advent of kdump, the assumption that the boot CPU when booting an UP
kernel is always the CPU with a particular hardware ID (often 0) (usually
referred to as BSP on some architectures) is not valid anymore. The reason
being that the dump capture kernel boots on the crashed CPU (the CPU that
invoked crash_kexec), which may be or may not be that particular CPU.
Move definition of hard_smp_processor_id for the UP case to
architecture-specific code ("asm/smp.h") where it belongs, so that each
architecture can provide its own implementation.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the sun4u controllers do the same thing to compute the physical
I/O address to poke, and we can move the sun4v code into this common
location too.
This one needs a bit of testing, in particular the Sabre code had some
funny stuff that would break up u16 and/or u32 accesses into pieces
and I didn't think that was needed any more. If it is we need to find
out why and add back code to do it again.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use IRQF_SHARED, these interrupt numbers should all
be unique.
Also use name strings without spaces in them just like
PCI controller drivers do, for consistency.
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea is to move more and more things into the pbm,
with the eventual goal of eliminating the pci_controller_info
entirely as there really isn't any need for it.
This stage of the transformations requires some reworking of
the PCI error interrupt handling.
It might be tricky to get rid of the pci_controller_info parenting for
a few reasons:
1) When we get an uncorrectable or correctable error we want
to interrogate the IOMMU and streaming cache of both
PBMs for error status. These errors come from the UPA
front-end which is shared between the two PBM PCI bus
segments.
Historically speaking this is why I choose the datastructure
hierarchy of pci_controller_info-->pci_pbm_info
2) The probing does a portid/devhandle match to look for the
'other' pbm, but this is entirely an artifact and can be
eliminated trivially.
What we could do to solve #1 is to have a "buddy" pointer from one pbm
to another.
Signed-off-by: David S. Miller <davem@davemloft.net>
Namely bus-range and ino-bitmap.
This allows us also to eliminate pci_controller_info's
pci_{first,last}_busno fields as only the pbm ones are
used now.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement utimensat(2) which is an extension to futimesat(2) in that it
a) supports nano-second resolution for the timestamps
b) allows to selectively ignore the atime/mtime value
c) allows to selectively use the current time for either atime or mtime
d) supports changing the atime/mtime of a symlink itself along the lines
of the BSD lutimes(3) functions
For this change the internally used do_utimes() functions was changed to
accept a timespec time value and an additional flags parameter.
Additionally the sys_utime function was changed to match compat_sys_utime
which already use do_utimes instead of duplicating the work.
Also, the completely missing futimensat() functionality is added. We have
such a function in glibc but we have to resort to using /proc/self/fd/* which
not everybody likes (chroot etc).
Test application (the syscall number will need per-arch editing):
#include <errno.h>
#include <fcntl.h>
#include <time.h>
#include <sys/time.h>
#include <stddef.h>
#include <syscall.h>
#define __NR_utimensat 280
#define UTIME_NOW ((1l << 30) - 1l)
#define UTIME_OMIT ((1l << 30) - 2l)
int
main(void)
{
int status = 0;
int fd = open("ttt", O_RDWR|O_CREAT|O_EXCL, 0666);
if (fd == -1)
error (1, errno, "failed to create test file \"ttt\"");
struct stat64 st1;
if (fstat64 (fd, &st1) != 0)
error (1, errno, "fstat failed");
struct timespec t[2];
t[0].tv_sec = 0;
t[0].tv_nsec = 0;
t[1].tv_sec = 0;
t[1].tv_nsec = 0;
if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
error (1, errno, "utimensat failed");
struct stat64 st2;
if (fstat64 (fd, &st2) != 0)
error (1, errno, "fstat failed");
if (st2.st_atim.tv_sec != 0 || st2.st_atim.tv_nsec != 0)
{
puts ("atim not reset to zero");
status = 1;
}
if (st2.st_mtim.tv_sec != 0 || st2.st_mtim.tv_nsec != 0)
{
puts ("mtim not reset to zero");
status = 1;
}
if (status != 0)
goto out;
t[0] = st1.st_atim;
t[1].tv_sec = 0;
t[1].tv_nsec = UTIME_OMIT;
if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
error (1, errno, "utimensat failed");
if (fstat64 (fd, &st2) != 0)
error (1, errno, "fstat failed");
if (st2.st_atim.tv_sec != st1.st_atim.tv_sec
|| st2.st_atim.tv_nsec != st1.st_atim.tv_nsec)
{
puts ("atim not set");
status = 1;
}
if (st2.st_mtim.tv_sec != 0 || st2.st_mtim.tv_nsec != 0)
{
puts ("mtim changed from zero");
status = 1;
}
if (status != 0)
goto out;
t[0].tv_sec = 0;
t[0].tv_nsec = UTIME_OMIT;
t[1] = st1.st_mtim;
if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
error (1, errno, "utimensat failed");
if (fstat64 (fd, &st2) != 0)
error (1, errno, "fstat failed");
if (st2.st_atim.tv_sec != st1.st_atim.tv_sec
|| st2.st_atim.tv_nsec != st1.st_atim.tv_nsec)
{
puts ("mtim changed from original time");
status = 1;
}
if (st2.st_mtim.tv_sec != st1.st_mtim.tv_sec
|| st2.st_mtim.tv_nsec != st1.st_mtim.tv_nsec)
{
puts ("mtim not set");
status = 1;
}
if (status != 0)
goto out;
sleep (2);
t[0].tv_sec = 0;
t[0].tv_nsec = UTIME_NOW;
t[1].tv_sec = 0;
t[1].tv_nsec = UTIME_NOW;
if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
error (1, errno, "utimensat failed");
if (fstat64 (fd, &st2) != 0)
error (1, errno, "fstat failed");
struct timeval tv;
gettimeofday(&tv,NULL);
if (st2.st_atim.tv_sec <= st1.st_atim.tv_sec
|| st2.st_atim.tv_sec > tv.tv_sec)
{
puts ("atim not set to NOW");
status = 1;
}
if (st2.st_mtim.tv_sec <= st1.st_mtim.tv_sec
|| st2.st_mtim.tv_sec > tv.tv_sec)
{
puts ("mtim not set to NOW");
status = 1;
}
if (symlink ("ttt", "tttsym") != 0)
error (1, errno, "cannot create symlink");
t[0].tv_sec = 0;
t[0].tv_nsec = 0;
t[1].tv_sec = 0;
t[1].tv_nsec = 0;
if (syscall(__NR_utimensat, AT_FDCWD, "tttsym", t, AT_SYMLINK_NOFOLLOW) != 0)
error (1, errno, "utimensat failed");
if (lstat64 ("tttsym", &st2) != 0)
error (1, errno, "lstat failed");
if (st2.st_atim.tv_sec != 0 || st2.st_atim.tv_nsec != 0)
{
puts ("symlink atim not reset to zero");
status = 1;
}
if (st2.st_mtim.tv_sec != 0 || st2.st_mtim.tv_nsec != 0)
{
puts ("symlink mtim not reset to zero");
status = 1;
}
if (status != 0)
goto out;
t[0].tv_sec = 1;
t[0].tv_nsec = 0;
t[1].tv_sec = 1;
t[1].tv_nsec = 0;
if (syscall(__NR_utimensat, fd, NULL, t, 0) != 0)
error (1, errno, "utimensat failed");
if (fstat64 (fd, &st2) != 0)
error (1, errno, "fstat failed");
if (st2.st_atim.tv_sec != 1 || st2.st_atim.tv_nsec != 0)
{
puts ("atim not reset to one");
status = 1;
}
if (st2.st_mtim.tv_sec != 1 || st2.st_mtim.tv_nsec != 0)
{
puts ("mtim not reset to one");
status = 1;
}
if (status == 0)
puts ("all OK");
out:
close (fd);
unlink ("ttt");
unlink ("tttsym");
return status;
}
[akpm@linux-foundation.org: add missing i386 syscall table entry]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the die notifier handling to common code. Previous
various architectures had exactly the same code for it. Note that the new
code is compiled unconditionally, this should be understood as an appel to
the other architecture maintainer to implement support for it aswell (aka
sprinkling a notify_die or two in the proper place)
arm had a notifiy_die that did something totally different, I renamed it to
arm_notify_die as part of the patch and made it static to the file it's
declared and used at. avr32 used to pass slightly less information through
this interface and I brought it into line with the other architectures.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix vmalloc_sync_all bustage]
[bryan.wu@analog.com: fix vmalloc_sync_all in nommu]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
apb_calc_first_last(), apb_fake_ranges(), pci_of_scan_bus(),
of_scan_pci_bridge(), pci_of_scan_bus(), and pci_scan_one_pbm()
should all be __devinit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor refactoring in the generic code was necessary for
this:
1) This controller requires 8-byte access to the interrupt map
and clear register. They are 64-bits on all the other
SBUS and PCI controllers anyways, so this was easy to cure.
2) The IMAP register has a different layout and some bits that we
need to preserve, so use a read/modify/write when making
changes to the IMAP register in generic code.
3) Flushing the entire IOMMU TLB is best done with a single write
to a register on this PCI controller, add a iommu->iommu_flushinv
for this.
Still lacks MSI support, that will come later.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_irq_msi() currently connects an irq_desc to an msi_desc. The archs call
it at some point in their setup routine, and then the generic code sets up the
reverse mapping from the msi_desc back to the irq.
set_irq_msi() should do both connections, making it the one and only call
required to connect an irq with it's MSI desc and vice versa.
The arch code MUST call set_irq_msi(), and it must do so only once it's sure
it's not going to fail the irq allocation.
Given that there's no need for the arch to return the irq anymore, the return
value from the arch setup routine just becomes 0 for success and anything else
for failure.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let's allow page-alignment in general for per-cpu data (wanted by Xen, and
Ingo suggested KVM as well).
Because larger alignments can use more room, we increase the max per-cpu
memory to 64k rather than 32k: it's getting a little tight.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This starts bringing the PowerPC and Sparc64 implemetations back closer
together.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helps deal with the invisible bridge that sits between
the host controller and the top-most visisble PCI devices
on hypervisor systems.
For example, on T1000 the bus-range property says 2 --> 4
and so there is a PCI express bridge at bus 2, devfn 0, etc.
So if we don't force the dummy host controller to bus zero,
we'll try to create two devices with the same domain/bus/devfn
triplet.
Also, add some more log diagnostics to make debugging stuff like this
easyer.
Signed-off-by: David S. Miller <davem@davemloft.net>
We fake up a dummy one in all cases because that is the simplest
thing to do and it happens to be necessary for hypervisor systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't do the "Simba APB is a PBM" bogosity for Sabre
controllers any longer, so this pbms_same_domain thing
is no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIMBA APB bridge is strange, it is a PCI bridge but it lacks
some standard OF properties, in particular it lacks a 'ranges'
property.
What you have to do is read the IO and MEM range registers in
the APB bridge to determine the ranges handled by each bridge.
So fill in the bus resources by doing that.
Since we now handle this quirk in the generic PCI and OF device
probing layers, we can flat out eliminate all of that code from
the sabre pci controller driver.
In fact we can thus eliminate completely another quirk of the sabre
driver. It tried to make the two APB bridges look like PBMs but that
makes zero sense now (and it's questionable whether it ever made sense).
So now just use pbm_A and probe the whole PCI hierarchy using that as
the root.
This simplification allows many future cleanups to occur.
Also, I've found yet another quirk that needs to be worked around
while testing this. You can't use the 'class-code' OF firmware
property, especially for IDE controllers. We have to read the value
out of PCI config space or else we'll see the value the device was
showing before it was programmed into native mode.
I'm starting to think it might be wise to just read all of the values
out of PCI config space instead of using the OF properties. :-/
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to traverse recursively down child busses else we only
get the file created under devices at the top-level.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user was bus_dvma_to_mem() which is no longer used
by any driver, so kill that, and the export of pci_memspace_mask.
The only user now is the PCI mmap support code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Almost entirely taken from the 64-bit PowerPC PCI code.
This allowed to eliminate a ton of cruft from the sparc64
PCI layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, do not try to compute resources by hand, instead use
the pre-computed ones in the of_device.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to simplify sharing code with powerpc which
has properties that have various forms of capitalization
when on the sparc64 side the property is all lower-case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, we actually change the functions themselves.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removes days_in_mo[], as it's almost identical to month_days[]
- Use the leapyear() macro
- Line length wrapping.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'd like to thank John Stul and others for helping
me along the way.
A lot of cleanups fell out of this. For example, the get_compare()
tick_op was totally unused, so was deleted. And the most often used
tick_op members were grouped together for cache-friendlyness.
The sparc64 TSC is given to the kernel as a one-shot timer.
tick_ops->init_timer() simply turns off the privileged bit in
the tick register (when possible), and disables the interrupt
by setting bit 63 in the compare register. The ->disable_irq()
op also sets this bit.
tick_ops->add_compare() is changed to:
1) Add the given delta to "tick" not to "compare"
2) Return a boolean which, if true, means that the tick
value read after writing the compare value was found
to have incremented past the initial tick value. This
mirrors logic used in the HPET driver's ->next_event()
method.
Each tick_ops implementation also now provides a name string.
And we feed this into the clocksource and clockevents layers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Things were scattered all over the place, split between
SMP and non-SMP.
Unify it all so that dyntick support is easier to add.
Signed-off-by: David S. Miller <davem@davemloft.net>
While building a test kernel for the new esp driver (against
git-current), I hit this bug. Trivial fix, put the inline declaration
in the right place. :)
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not sign extend args using the sys32_ipc stub, that is
buggy and unnecessary.
Based upon an excellent report by Mikael Pettersson.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix section mismatch in arch/sparc/kernel/pcic.c and
arch/sparc64/kernel/pci.c.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't figure anyone really cares about SunOS syscall emulation, and I
certainly don't. But I'm getting rid of uses of the OPEN_MAX and CHILD_MAX
compile-time constant, and these are almost the only ones. OPEN_MAX is a
bogus constant with no meaning about anything. The RLIMIT_NOFILE resource
limit is what sysconf (_SC_OPEN_MAX) actually wants to return.
The CHILD_MAX cases weren't actually using anything I want to get rid of,
but I noticed that they are there and are wrong too. The CHILD_MAX value
is not really unlimited as a -1 return from sysconf indicates. The
RLIMIT_NPROC resource limit is what sysconf (_SC_CHILD_MAX) wants to return.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several IOMMU allocator bugs. Instead of trying to fix this
overly complicated code, just mirror the PCI IOMMU arena allocator
which is very stable and well stress tested.
I tried to make the code as identical as possible so we can switch
sun4u PCI and SBUS over to a common piece of IOMMU code. All that
will be need are two callbacks, one to do a full IOMMU flush and one
to do a streaming buffer flush.
This patch gets rid of a lot of hangs and mysterious crashes on SBUS
sparc64 systems, at least for me.
Signed-off-by: David S. Miller <davem@davemloft.net>
