* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix sysfs_create_file return value handling
[CPUFREQ] ondemand: fix tickless accounting and software coordination bug
[CPUFREQ] ondemand: add a check to avoid negative load calculation
[CPUFREQ] Keep userspace governor quiet when it is not being used
[CPUFREQ] Longhaul - Proper register access
[CPUFREQ] Kconfig powernow-k8 driver should depend on ACPI P-States driver
[CPUFREQ] Longhaul - Replace ACPI functions with direct I/O
[CPUFREQ] Longhaul - Remove duplicate multipliers
[CPUFREQ] Longhaul - Embedded "conservative"
[CPUFREQ] acpi-cpufreq: Proper ReadModifyWrite of PERF_CTL MSR
[CPUFREQ] check return value of sysfs_create_file
[CPUFREQ] Longhaul - Check ACPI "BM DMA in progress" bit
[CPUFREQ] Longhaul - Move old_ratio to correct place
[CPUFREQ] Longhaul - VT8237 support
[CPUFREQ] Longhaul - Use all kinds of support
[CPUFREQ] powernow-k8: clarify number of cores.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Support multiple CPUs going through OS_MCA
[IA64] silence GCC ia64 unused variable warnings
[IA64] prevent MCA when performing MMIO mmap to PCI config space
[IA64] add sn_register_pmi_handler oemcall
[IA64] Stop bit for brl instruction
[IA64] SN: Correct ROM resource length for BIOS copy
[IA64] Don't set psr.ic and psr.i simultaneously
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
sysfs: make directory dentries and inodes reclaimable
sysfs: implement sysfs_get_dentry()
sysfs: move sysfs_drop_dentry() to dir.c and make it static
sysfs: restructure add/remove paths and fix inode update
sysfs: use sysfs_mutex to protect the sysfs_dirent tree
sysfs: consolidate sysfs spinlocks
sysfs: make kobj point to sysfs_dirent instead of dentry
sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
sysfs: implement SYSFS_FLAG_REMOVED flag
sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
sysfs: make sysfs_drop_dentry() access inodes using ilookup()
sysfs: Fix oops in sysfs_drop_dentry on x86_64
sysfs: use singly-linked list for sysfs_dirent tree
sysfs: slim down sysfs_dirent->s_active
sysfs: move s_active functions to fs/sysfs/dir.c
sysfs: fix root sysfs_dirent -> root dentry association
sysfs: use iget_locked() instead of new_inode()
sysfs: reorganize sysfs_new_indoe() and sysfs_create()
sysfs: fix parent refcounting during rename and move
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: remove irq_on from ata_bus_reset() and ata_std_postreset()
ata_piix: kill incorrect invalid map value warning
libata: add another Maxtor drive with broken NCQ to the list
[libata] sata_mv: Fix and clean up per-chip-generation tests
[libata] sata_mv: Convert to new exception handling (EH) infrastructure
[libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
[libata] sata_mv: Minor cleanups and renaming, preparing for new EH & NCQ
libata-link: add PMP related ATA constants
libata-link: separate out ata_eh_handle_dev_fail()
pata_hpt3x3: fix DMA Kconfig option to actually have a hope of working
Add Hitachi HDS7250SASUN500G 0621KTAWSD to NCQ blacklist
pata_scc.c: Workaround for errata A308
libata: add FUJITSU MHV2080BH to NCQ blacklist
pata_hpt3x3: major reworking and testing
libata: clean up horkage handling
libata: quirk IOMEGA ZIP 250 ATAPI FLOPPY
libata: simplify PCI legacy SFF host handling
pata_mpc52xx: suspend/resume support
sata_promise: SATA hotplug support, take 2
pata_sis: FIFO whack
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
* master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin serial driver: supporting BF548-EZKIT serial port
Video Console: Blackfin doesnt support VGA console
Blackfin arch: Add peripheral io API to gpio header file
Blackfin arch: set up gpio interrupt IRQ_PJ9 for BF54x ATAPI PATA driver
Blackfin arch: add missing CONFIG_LARGE_ALLOCS when upstream merging
Blackfin arch: as pointed out by Robert P. J. Day, update the CPU_FREQ name to match current Kconfig
Blackfin arch: extract the entry point from the linked kernel
Blackfin arch: clean up some coding style issues
Blackfin arch: combine the common code of free_initrd_mem and free_initmem
Blackfin arch: Add Support for Peripheral PortMux and resouce allocation
Blackfin arch: use PAGE_SIZE when doing aligns rather than hardcoded values
Blackfin arch: fix bug set dma_address properly in dma_map_sg
Blackfin arch: Disable CACHELINE_ALIGNED_L1 for BF54x by default
Blackfin arch: Port the dm9000 driver to Blackfin by using the correct low-level io routines
Blackfin arch: There is no CDPRIO Bit in the EBIU_AMGCTL Register of BF54x arch
Blackfin arch: scrub dead code
Blackfin arch: Fix Warning add some defines in BF54x header file
Blackfin arch: add BF54x missing GPIO access functions
Blackfin arch: Some memory and code optimizations - Fix SYS_IRQS
Blackfin arch: Enable BF54x PIN/GPIO interrupts
...
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (26 commits)
i2c-rpx: Remove
i2c-mpc: work around missing-9th-clock-pulse bug
i2c: New PMC MSP71xx TWI bus driver
i2c-savage4: Delete many unused defines
i2c/tsl2550: Speed up initialization
i2c: New bus driver for the TAOS evaluation modules
i2c-i801: Use the internal 32-byte buffer on ICH4+
i2c-i801: Various cleanups
i2c: Add support for the TSL2550
i2c-pxa: Support new-style I2C drivers
i2c-gpio: Make some internal functions static
i2c-gpio: Add support for new-style clients
i2c-iop3xx: Switch to static adapter numbering
i2c-sis5595: Resolve resource conflict with sis5595
matroxfb: Clean-up i2c header inclusions
i2c-nforce2: Add support for SMBus block transactions
i2c-mpc: Use i2c_add_numbered_adapter
i2c-mv64xxx: Use i2c_add_numbered_adapter
i2c-piix4: Add support for the ATI SB700
i2c: New DS1682 chip driver
...
It seems irq_on() in ata_bus_reset() and ata_std_postreset()
are leftover of the EDD reset. Remove them.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The last two slots of MAP 00b of ich6m was incorrectly marked as
reserved. This is left over from converting the entry to allow 00b.
This causes no real problem. It only makes the driver print annoying
warning message. Fix it.
[patch also proferred by Pierre Tardy at the end of 2006 -jg]
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
drivers/ata/ata_piix.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add another Maxtor 6B200M0 drive with broken NCQ to the list.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Due to a mistake in test logic, Gen-IIE chips were being treated as
Gen-II chips in some cases. Fix this, and in the process, clean up
IS_50XX/IS_60XX tests to the more uniform IS_GEN_{I,II,IIE} tests.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Continue replacing "CONSTANT & var" tests with "var & CONSTANT"
* Don't clear EDMA_CFG_NCQ_GO_ON_ERR on Gen-IIE, where that bit does
not exist
* Set I/O Id field in descriptor, where present. Appears to work
fine on all versions, even though queueing is still disabled.
* call pci_set_mwi(), to (a) make sure cacheline size is set properly,
and (b) enable MWI transactions
* Remove never-used handling of coalescing interrupt bits (these events
are always masked)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An ST-506 disk these days is pretty much someone trying to pull ancient
data using an auxilliary controller. Pulling data from the BIOS or CMOS
is just plain wrong, since it's likely to be the primary OS disk... and
would be user-entered data anyway. Instead, require the user enters it
on the command line.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only pseudo-legitimate MIPS user of genrtc was a systems that doesn't
have an RTC in hardware at all. At this point faking one is a little
pointless ...
pxamci.h redefines the MMC registers differently so they can be used
with ioremap. Remove the incompatible definitions from pxa-regs.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver has been broken forever. It depends on i2c-algo-8xx which
has never been in the mainline kernel.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Work around a problem reported on:
http://ozlabs.org/pipermail/linuxppc-embedded/2005-July/019038.html
Without this patch I2C on mpc5200 becomes unusable after a while.
Tested on mpc5200 boards by Matthias Fechner and me.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add TWI driver for the PMC-Sierra MSP71xx devices.
[JD: Drop the probe hack, don't set algo_data as we never use it, return
the right error code if the driver registration fails.]
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There's some redundancy in the tsl2550 initialization sequence. It is
powering up the device twice, and setting the operating mode twice
too. Setting things just once saves SMBus transactions, which aren't
always cheap, speeding up the device initialization.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
This is a new I2C bus driver for the TAOS evaluation modules. Developped
and tested on the TAOS TSL2550 EVM.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add an ability to utilize the internal SRAM buffer on ICH4
and newer host controllers to speed up execution of block operations.
I've split the code so that it is more clear which block transaction is
performed.
First of all the host controller's type is identified. isich4 is set when
we think that the controller has the internal buffer. Then, before every
block transaction, if isich4 is set, we attempt to enable the E32B bit in
SMBAUXCTL register.
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* Use defines instead of raw numbers for register bits
* Fix several wrong indentations and trailing whitespace
* Move hwpec timeout checking to a separate function
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_gpio_getsda() and i2c_gpio_getscl() are only used in this file.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use i2c_bit_add_numbered_bus() so that the i2c-gpio adapter works well
with new-style pre-declared devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update the IOP3xx I2C driver to use i2c_add_numbered_adapter(), so that
later patches can convert boards to using new-style drivers.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Voipio Riku <Riku.Voipio@movial.fi>
Cc: Dan J Williams <dan.j.williams@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the i2c-sis5595 driver release its PCI device after registering.
This is to allow the sis5595 hardware monitoring driver to also
access this PCI device. The same trick is already used in the
i2c-viapro and via686a drivers to let them both load.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
matroxfb_crtc2 has nothing to do with i2c, so there's no reason why
matroxfb_crtc2.h should include i2c header files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Add support for SMBus block read/write transactions to i2c-nforce2
driver, in particular to host controllers MCP51 and MCP55.
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the i2c-mpc driver over to using the new i2c infrastructure.
Specifically, it now uses i2c_add_numbered_adapter so that the bus number
can be determined ahead of time and used to register i2c clients before
the bus is instantiated.
Tested on an MPC5200 based board
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the Marvell mv64xxx I2C driver to use the new i2c infrastructure,
by calling i2c_add_numbered_adapter(). This allows clients to be
registered before the bus is instantiated.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A driver for the Dallas DS1682 elapsed time recorder chip.
Tested on a MPC5200 based board using the integrated i2c adapter.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the drivers specify how many bytes they want to read with
i2c_smbus_read_i2c_block_data(). So far, the block count was
hard-coded to I2C_SMBUS_BLOCK_MAX (32), which did not make much sense.
Many driver authors complained about this before, and I believe it's
about time to fix it. Right now, authors have to do technically stupid
things, such as individual byte reads or full-fledged I2C messaging,
to work around the problem. We do not want to encourage that.
I even found that some bus drivers (e.g. i2c-amd8111) already
implemented I2C block read the "right" way, that is, they didn't
follow the old, broken standard. The fact that it was never noticed
before just shows how little i2c_smbus_read_i2c_block_data() was used,
which isn't that surprising given how broken its prototype was so far.
There are some obvious compatiblity considerations:
* This changes the i2c_smbus_read_i2c_block_data() prototype. Users
outside the kernel tree will notice at compilation time, and will
have to update their code.
* User-space has access to i2c_smbus_xfer() directly using i2c-dev, so
the changed expectations would affect tools such as i2cdump. In order
to preserve binary compatibility, we give I2C_SMBUS_I2C_BLOCK_DATA
a new numeric value, and define I2C_SMBUS_I2C_BLOCK_BROKEN with the
old numeric value. When i2c-dev receives a transaction with the
old value, it can convert it to the new format on the fly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have a new RTC subsystem with better drivers.
Legacy driver status:
* ds1337: The DS1337 and DS1339 are now supported by the rtc-ds1307
driver, so it looks to me like we could even delete the ds1337
driver right away.
* ds1374: Will soon be replaced with Scott Wood's rtc-ds1374 driver.
* m41t00: The M41T00 is supported by the rtc-ds1307 driver. For the
M41T81 and M41T85, the rtc-m41t80 driver written by Atsushi Nemoto
should work.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: James Chapman <jchapman@katalix.com>
Cc: Randy Vinson <rvinson@mvista.com>
The x1205 driver moved to the RTC subsystem and was significantly
modified since then, so just delete the outdated documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
The scx200_acb driver use a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Generate I2C kerneldoc; fix various glitches and add "context" sections to
that documentation. Most I2C and SMBus functions still have no kerneldoc.
Let me suggest providing kerneldoc for all the i2c_smbus_*() functions as
a small and mostly self-contained project for anyone so inclined. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
