Commit Graph

21 Commits

Author SHA1 Message Date
Mike Christie
d8196ed218 [SCSI] iscsi class, iscsi_tcp, iser, qla4xxx: add netdevname sysfs attr
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:38:04 -04:00
Mike Christie
2223696192 [SCSI] iscsi class, qla4xxx, iscsi_tcp: export local address
This patch exports the local address for the session. For
qla4xxx this is the ip of the hba's port. For software
this is the src addr of the socket.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:37:19 -04:00
Mike Christie
1548271ece [SCSI] libiscsi: make can_queue configurable
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:46 -04:00
Mike Christie
77a23c21aa [SCSI] libiscsi: fix iscsi cmdsn allocation
The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:14 -04:00
Mike Christie
b2c6416736 [SCSI] iscsi class, iscsi_tcp, ib_iser: add sysfs chap file
The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:58 -04:00
Mike Christie
857ae0bdb7 [SCSI] iscsi: Some fixes in preparation for bidirectional support - total_length
- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly

(With bidi we will use scsi-ml API to retrieve in/out length)

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:22 -04:00
Mike Christie
d473cc7f15 [SCSI] iscsi: Some fixes in preparation for bidirectional support - exp_datasn
This patch fixes handling of expected datasn/r2tsn as received from
target. It is done according to: T10 rfc3720 section 3.2.2.3. Data Sequencing.

. unify expected datasn/r2tsn into one counter
. calculate than check expected datasn/r2tsn. On error print a message
  and fail the request. (TODO use iscsi retransmits)
. remove the FIXME   ;)
. avoid zero length memset

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:57:17 -04:00
Mike Christie
8ad5781ae9 [SCSI] iscsi class, qla4xxx, iscsi_tcp, ib_iser: export/set initiator name
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.

For hw iscsi, it is nice to see what the card is using.

This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:56:40 -04:00
Mike Christie
0801c242a3 [SCSI] libiscsi, iscsi_tcp, ib_iser : add sw iscsi host get/set params helpers
iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.

Also convert them

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:55:23 -04:00
Al Viro
f6a570333e [PATCH] severing module.h->sched.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2006-12-04 02:00:22 -05:00
Mike Christie
9864404791 [SCSI] libiscsi: fix oops in connection create failure path
If connection creation fails we end up calling list_del
on a invalid struct. This then causes an oops. We are not
acutally using the lists (old MCS code we thought might
be useful elsewhere) so this patch just removes that
code.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-10-25 15:13:53 -07:00
Mike Christie
60ecebf5a1 [SCSI] add refcouting around ctask usage in main IO patch
It is possible that a ctask could be completing and getting
cleaned up at the same time, we are finishing up the last
data transfer. This could then result in the data transfer
code using stale or invalid values. This patch adds a refcount
to the ctask. When the count goes to zero then we know the
transmit thread and recv thread or softirq are not touching
it and we can safely release it.

The eh should not need to grab a reference because it only cleans
up a task if it has both the xmit mutex and recv lock (or recv
side suspended).

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:07 -05:00
Mike Christie
ffd0436ed2 [SCSI] libiscsi, iscsi_tcp, iscsi_iser: check that burst lengths are valid.
iSCSI RFC states that the first burst length must be smaller than the
max burst length. We currently assume targets will be good, but that may
not be the case, so this patch adds a check.

This patch also moves the unsol data out offset to the lib so the LLDs
do not have to track it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:04 -05:00
Mike Christie
c8dc1e523b [SCSI] iscsi bugfixes: reduce memory allocations
We currently try to allocate a max_recv_data_segment_length
which can be very large (default is 64K), and common uses
are up to 1MB. It is very very difficult to allocte this
much contiguous memory and it turns out we never even use it.
We really only need a couple of pages, so this patch has us
allocates just what we know what we need today.

Later if vendors start adding vendor specific data and
we need to handle large buffers we can do this, but for
the last 4 years we have not seen anyone do this or request
it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:49:34 -05:00
Mike Christie
7ea8b82847 [SCSI] iscsi bugfixes: fix abort handling
Abort handler fixes.

If a connection is dropped and reconnected while an abort is
running then we should assume the recovery code will clean up
the abort. Not doing so causes a oops.

And if a command completes then we get the status for the abort, we do not
need to call into the LLD to cleanup the resources. Doing this causes
and oops in iser because it ends up freeing some resources twice.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:48:16 -05:00
Mike Christie
b6c395ed03 [SCSI] iscsi bugfixes: fix r2t handling
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue
in the xmit code. This can result in the task being queued on the xmit queue
but gettting completed at the same time.

This patch fixes the above bug by making the fifo a list so
we always remove the entry on the list del.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:47:40 -05:00
Mike Christie
a54a52caad [SCSI] iscsi: fixup set/get param functions
Reduce duplication in the software iscsi_transport modules by
adding a libiscsi function to handle the common grunt work.

This also has the drivers return specifc -EXXX values for different
errors so userspace can finally handle them in a sane way.

Also just pass the sysfs buffers to the drivers so HW iscsi can
get/set its string values, like targetname, and initiatorname.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-29 11:07:14 -04:00
Mike Christie
67a611149b [SCSI] iscsi: don't switch states when just cleaning up
If recovery failed or we are in recovery only overwrite the state
if we are going to terminate the session or if we logged back in.

STOP_CONN_SUSPEND and conn_cnt are not used. We only support
a single connection session ATM, so cleanup that code while
we are working around it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-05 19:10:45 -04:00
Mike Christie
656cffc95f [SCSI] iscsi: fix command requeues during iscsi recovery
Do not flush queues then block session. This will cause commands
to needlessly swing around on us and remove goofy
recovery_failed field and replace with state value.

And do not start recovery from within the host reset function.
This causeis too many problems becuase open-iscsi was desinged to
call out to userspace then have userpscae decide if we should
go into recovery or kill the session.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-20 09:36:17 -05:00
Or Gerlitz
be2df72e7e [SCSI] iscsi: align printks
align printk output

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-10 10:12:52 -05:00
Mike Christie
7996a778ff [SCSI] iscsi: add libiscsi
There is a lot of code duplcited between iscsi_tcp
and the upcoming iscsi_iser driver. This patch puts
the duplicated code in a lib. There is more code
to move around but this takes care of the
basics. For iscsi_offload if they use the lib we will
probably move some things around. For example in the
queuecommand we will not assume that the LLD wants
to do queue_work, but it is better to handle that
later when we know for sure what iscsi_offload looks
like (we could probably do this for iscsi_iser though to).

Ideally I would like to get the iscsi_transports modules
to a place where all they really have to do is put data
on the wire, but how to do that will hopefully be more clear
when we see other modules like iscsi_offload. Or maybe
iscsi_offload will not use the lib and it will just be
iscsi_iser and iscsi_tcp and maybe the iscsi_tcp_tgt if that
is allowed in mainline.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-04-14 14:09:00 -05:00