Be more precise on deciding whether to call m8xx_ide_init() at
m8xx_setup.c:platform_init().
Compilation fails if CONFIG_BLK_DEV_IDE is defined but
CONFIG_BLK_DEV_MPC8xx_IDE isnt.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes build on 4xx stb03xxx when general purpose dma engine support is
enabled.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory mappings for MPC8349 USB MPH and DR modules were reversed.
Signed-off-by: Li Yang <LeoLi@freescale.com>
Signed-off-by: Jiang Bo <Tanya.jiang@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Touching the pte directly causes the 8Mbyte TLB entry to be invalidated.
This has been fixed in v2.4 for ages.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add PPC440EP core support. PPC440EP is a PPC440-based SoC with a classic PPC
FPU and another set of peripherals.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo bug that was using PCI1 defines instead of PCI2 when setting up the
second PCI bus controller on 85xx based systems. This hasn't been a real
issue since currently the PCI2 sizes are the same as the PCI1 sizes for
currently supported boards.
Thanks to Andrew Klossner @ Xerox for point this out.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 2.6.12.3 kernel compilation fails for ARCH=ppc when CONFIG_PQ2FADS=y.
This patch has been tested on Freescale PQ2FADS-ZU and -VR boards.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The UARTs on the MPC824x are unique devices and really shouldn't be thought
of as a DUART. In addition, if both UARTs are in use we need to configure
the part to enable the 2nd UART since the pins for the UARTs are
multiplexed. Adds support to run the 824x Sandpoint with both UARTs if
desired.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added a proper prototype for cpm2_reset() which gets rid of a build
warning.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the usage of struct of_match to struct of_device_id,
similar to pci_device_id. This allows a device table to be generated,
which can be parsed by depmod(8) to generate a map file for module
loading.
In order for hotplug to work with macio devices, patches to
module-init-tools and hotplug must be applied. Those patches are
available at:
ftp://ftp.suse.com/pub/people/jeffm/linux/macio-hotplug/
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add explicit disabling of 440GP IRQ compatibility mode when configuring
440GX interrupt controller. This helps when board firmware for some reason
uses this compatibility mode and leaves it enabled. It breaks 440GX
interrupt code because it assumes native 440GX IRQ mode. People seems to
be continuously bitten by this.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Power Management Unit on PowerMacs is very sensitive to timeouts during
async message exchanges. It uses rather crude protocol based on a shift
register with an interrupt and is almost continuously exchanging messages with
the host CPU on laptops.
This patch adds a routine to the open_pic driver to be able to select a PMU
driver so that it bumps it's interrupt priority to above the normal level.
This will allow PMU interrupts to occur while another interrupt is pending,
and thus reduce the risk of machine beeing abruptly shutdown by the PMU due to
a timeout in PMU communication caused by excessive interrupt latency. The
problem is very rare, and usually just doesn't happen, but it is still useful
to make things even more robust.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pending registers for IRQ1-IRQ7 were pointing to the interrupt pending
register instead of the external one.
Signed-off-by: Tony Li <Tony.Li@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Continue the Good Fight: Limit bootmem.h include creep.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fight the Good Fight: Limit prom.h header creep.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removes ppc4xx_kgdb.c which is no longer being used. Pointed out by Andrei
Konovalov.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added platform device initialization for the two 8250 style UARTs that
exist on the MPC8245. Additionally, updated the Sandpoint code to enable
one of these UARTs if an MPC8245 is connected to it.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Converted the MPC10x bridge support (used by MPC10x and 8240/1/5) to used
the standard platform device model.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously we needed CONFIG_CPM2 enabled to get the proper IRQ ifdef's for
CPM interrupts. Recent changes have caused that to be no longer necessary.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for using the MPC8548 processor on the CDS reference board.
Currently all the major busses (PCI, PCI-X, PCI-Express, sRIO) and eTSEC3
and eTSEC4 are not supported.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added descriptions of the new MPC8548 family processors, e500 core and
peripherals.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the ppc32 patch equivalent to the just posted ppc64 one working
around a bug in Apple device-trees regarding the "cpus" nodes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change allows mpc83xx_restart to issue a software reset.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds on-chip PCI bridge support for the PQ2 family. The
incomplete existent code is updated with interrupt handling stuff and
board-specific bits for 8272ADS and PQ2FADS; the related files were renamed
(from m8260_pci to m82xx_pci) to be of more generic fashion. This is
tested with 8266ADS and 8272ADS, should work on PQ2FADS as well.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the VIA IDE controller that exists on the MPC8555 CDS
system. Updated the config for the system to enable support by default.
Signed-off-by: Scott Hall <shall@mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent kernels occasionally trigger a PMU timeout on some mac laptops,
typically on wakeup from sleep. This seem to be caused by either a too big
latency caused by the cpufreq switch on wakeup from sleep or by an
interrupt beeing lost due to the reset of the interrupt controller done
during wakeup.
This patch makes that code more robust by stopping PMU auto poll activity
around cpufreq changes on machines that use the PMU for such changes (long
latency switching involving a CPU hard reset and flush of all caches) and
by removing the reset of the open pic interrupt controller on wakeup (that
can cause the loss of an interrupt and Darwin doesn't do it, so it must not
be necessary).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is an off-by-one error in the IPIC code that configures the
external interrupts (Edge or Level Sensitive).
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialization of 8250 serial ports that are platform devices require that
at empty entry exists in the array of plat_serial8250_port. With out an
empty entry we can get some pretty random behavior.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are computing phys in the code below and never using. This patch
takes out the redundant computation.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a problem with large amounts of spurious IRQs on PowerPC 82xx
systems.
The problem is corrected by adding sync at the end of cpm2_mask_and_ack.
This may be needed on 8xx as well but has not yet been confirmed.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Dan Malek <dan@embeddedalley.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* ->io_base_virt in struct pci_controller is iomem pointer. Marked as such.
Most of the places that used it are already annotated to expect iomem.
* places that did gratitious (and wrong) casts a-la
isa_io_base = (unsigned long)ioremap(...);
hose->io_base_virt = (void *)isa_io_base;
turned into
hose->io_base_virt = ioremap(...);
isa_io_base = (unsigned long)hose->io_base_virt;
* pci_bus_io_base() annotated as returning iomem pointer.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make defconfig give the following error on ppc (gcc-4):
arch/ppc/syslib/open_pic.c:36: error: static declaration of ‘OpenPIC’ follows non-static declaration
arch/ppc/syslib/open_pic_defs.h:175: error: previous declaration of ‘OpenPIC’ was here
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CONFIG_8xx_WDT option got broken in the generic hardirq update as ppc32
had its own different request_irq that worked when other arches used
setup_irq. This is the trivial fix for the problem.
From: Carsten Juttner <carjay@gmx.net>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To add support for 36-bit physical addressing on e500 the following changes
have been made. The changes are generalized to support any physical address
size larger than 32-bits:
* Allow FSL Book-E parts to use a 64-bit PTE, it is 44-bits of pfn, 20-bits
of flags.
* Introduced new CPU feature (CPU_FTR_BIG_PHYS) to allow runtime handling of
updating hardware register (SPRN_MAS7) which holds the upper 32-bits of
physical address that will be written into the TLB. This is useful since
not all e500 cores support 36-bit physical addressing.
* Currently have a pass through implementation of fixup_bigphys_addr
* Moved _PAGE_DIRTY in the 64-bit PTE case to free room for three additional
storage attributes that may exist in future FSL Book-E cores and updated
fault handler to copy these bits into the hardware TLBs.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the PowerMac cpufreq driver. It depends on the addition
of the suspend() method (my previous patch) and on the new flag I defined
to silence some warnings that are normal for us.
It fixes various issues related to cpufreq on pmac, including some crashes
on some models when sleeping the machine while in low speed, proper voltage
control on some newer machines, and adds voltage control on 750FX based G3
laptops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds interrupt acknowledge to the PPC4xx PIC enable_irq
implementation for level-sensitive IRQ sources. This helps in cases when
enable/disable_irq is used in interrupt handlers for hardware, which
requires IRQ acknowledge to be issued from non-interrupt context (e.g.
when actual ACK in device needs an I2C transaction). For such strange
hardware, interrupt handler disables IRQ and defers actual ACK to some
other context. When this happens, IRQ is enabled again. For
level-sensitive sources we get spurious triggering right after IRQ is
enabled. This patch fixes this.
Suggested by Tolunay Orkun <listmember@orkun.us>.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
