This commit adds support for MOTU Traveler, launched in 2005, discontinued
quite before. As a result, transmission of PCM frame and MIDI messages is
available via ALSA PCM and RawMIDI/Sequencer interfaces.
This model supports sampling transmission frequency up to 192.0 kHz, and
AES/EBU on XLR interface and ADAT on optical interface. Unlike
Motu 828MkII, Windows driver can switch fetching mode for DSP, like
mute/unmute feature.
Although this commit enables high sampling transmission frequency, actual
sound from this model is not good. As long as I tested, it's silence at
176.4 kHz, and it includes hissing noise at 192.0 kHz. In my opinion, as I
reported at 3526ce7f9ba7 ('ALSA: firewire-motu: add MOTU specific protocol
layer'), timestamping on source packet header (SPH) may not still be good
for this model as well.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04106505 bus_info_length 4, crc_length 16, crc 25861
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 0001f32f device_id 000001f32f | EUI-64 0001f2000001f32f
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 00035955 directory_length 3, crc 22869
42c 120001f2 specifier id
430 13000009 version
434 17107800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000206b2 leaf_length 2, crc 1714
43c 0001f200 company_id 0001f2 |
440 0001f32f device_id 000001f32f | EUI-64 0001f2000001f32f
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For MOTU protocol version 2, this driver arranges the number of data
chunks to align chunks to quadlet data channel. However, MOTU Traveler
has padding bytes in the end of data block at high clock mode.
This commit removes the arrangement. Fortunately, at low and middle clock
mode, supported model for v2 protocol (828mkII) gets no influence from this
change because all of combination for data chunks are just aligned to
quadlet data channel.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU Traveler supports AES/EBU on XLR interface and data block of rx/tx
packet includes two chunk for the interface. This commit adds a flag
for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver explicitly assumes that all of supported models have main data
chunk separated from chunk for analog ports. However, MOTU Traveler doesn't
support the separated main data chunk.
This commit adds a flag for the separated main data chunk.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU firewire protocol, data block consists of 24 bit data chunks except
for one quadlet for source packet header (SPH). The number of data chunk in
a data block is different between three clock modes; low, middle and high.
When unit supports ADAT on optical interface, the data block includes some
chunks for ADAT channels. These ADAT chunks are unavailable at high mode.
This driver has local functions to calculate the number of ADAT chunks. But
They uses stack for three clock modes. This is useless for higher mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocols of MOTU FireWire series, when transferring MIDI messages,
transmitter set existence flag to one byte on first several quadlets. The
position differs depending on protocols and models, however two cases are
confirmed; in 5th byte and 8th byte from MSB side.
This commit adds a series of specification flag to describe them. When
the existence flag is in the 5th byte, SND_MOTU_SPEC_[R|T]X_MIDI_2ND_Q is
used. Else, another set of the flag is used. Here, '_Q' means quadlet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk2 is one of second generation in MOTU FireWire series, produced in
2003. This model consists of four chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* PDI 1394L40BE (Link layer for IEEE 1394 bus and packet processing layer)
* ALTERA ACEX 1K EP1K30 Series FPGA (Data block processing layer)
* TI TMS320VC5402 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 2. The features of this protocol are:
* Support data chunks for status and control messages for both
directions.
* Support a pair of MIDI input/output.
* Support a data chunk for mic/instrument independent of analog line in.
* Support a data chunk for playback return.
* Support independent data chunks for S/PDIF of both optical/coaxial
interfaces.
* Support independent data chunks for each of main out and phone out.
Status of clock is configured by write transactions to 0x'ffff'f000'0b14.
Modes of optical interfaces are configured by write transactions to
0x'ffff'f000'0c04.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
