# This file allows user to override the factory # defaults for the WLAN Driver # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 #Enable OBSS protection gEnableApOBSSProt=1 # Maximum Tx power # gTxPowerCap=30 # Fragmentation Threshold # gFragmentationThreshold=2346 # RTS threshold RTSThreshold=1048576 # WMM Enable/Disable WmmIsEnabled=0 # 802.11d support g11dSupportEnabled=0 # DFS Master Capability gEnableDFSMasterCap=1 ImplicitQosIsEnabled=0 gNeighborScanTimerPeriod=200 gNeighborLookupThreshold=76 gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 # Sets RSSI preference for 5GHz over 2.4GHz AP gSelect5GHzMargin=5 # HIGH RSSI roaming # RSSI threshold offset for 2G to 5G roam # default is 40 roam_bad_rssi_thresh_offset_2g=40 #RSSI threshold for background roam roam_bg_scan_bad_rssi_thresh=-76 # Candidate AP minimum RSSI for beacon miss roam trigger candidate_min_rssi_for_beacon_miss=-83 #Channel Bonding gChannelBondingMode5GHz=1 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link #is idle for last 10 seconds.) For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client #honors TIM bit. If doesn't honor for 5 seconds then DUT remove client. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not #success still we try on 11th second if not tries on 12th and so on till 15th #second. Hence before disconnection DUT will send 5 NULL frames. Hence in any #case DUT will detect client got removed in (10+5) seconds. #i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and #it is period where we send NULL frame. #gApLinkMonitorPeriod = 10 #gGoLinkMonitorPeriod = 10 #gApKeepAlivePeriod is time to spend to check whether frame #are succeed to send or not. Hence total effective detection time is #(gApLinkMonitorPeriod + gApKeepAlivePeriod) #Enable Keep alive with non-zero period value gStaKeepAlivePeriod = 30 # Enable DFS channel roam # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE gAllowDFSChannelRoam=1 gVhtChannelWidth=2 # Set txchainmask and rxchainmask # These parameters are used only if gEnable2x2 is 0 # Valid values are 1,2 # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. gSetTxChainmask1x1=1 gSetRxChainmask1x1=1 # MCC to SCC Switch mode: # 0-Disable # 1-Enable # 2-Force SCC if same band, with SAP restart # 3-Force SCC if same band, without SAP restart by sending (E)CSA # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, # without SAP restart by sending (E)CSA gWlanMccToSccSwitchMode = 3 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable rx STBC; 0=disable gEnableRXSTBC=0 #Enable/Disable Tx beamformee in SAP mode gEnableTxBFeeSAP=1 # Enable Tx beamforming in VHT20MHz # Valid values are 0,1. If commented out, the default value is 0. # 0=disable, 1=enable gEnableTxBFin20MHz=1 #Enable/Disable SU Tx beamformer support gEnableTxSUBeamformer=0 # 802.11K support gRrmEnable=1 #Enable Power Save offload gEnablePowerSaveOffload=2 # Firmware log mode # Valid values are 0,1,2 # 0=Disable, 1=WMI, 2=DIAG gEnablefwlog=0 # Maximum Receive AMPDU size (VHT only. Valid values: # 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum MPDU length (VHT only. Valid values: # 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=2 #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=0 # Set Thermal Power limit TxPower2g=10 TxPower5g=10 #Enable VHT on 2.4Ghz gEnableVhtFor24GHzBand=1 #Maximum number of offload peers supported # gMaxOffloadPeers=2 # controlling the following offload patterns # through ini parameter. Default value is 1 # to disable set it to zero. ssdp = 0 # Setup multicast pattern for mDNS 224.0.0.251, # SSDP 239.255.255.250 and LLMNR 224.0.0.252 ssdp=0 # RA filtering rate limit param, the current value would not # help if the lifetime in RA is less than 3*60=3min. Then # we need to change it, though it is uncommon. # gRAFilterEnable=0 gRArateLimitInterval=600 # Maximum number of concurrent connections gMaxConcurrentActiveSessions=3 # Disable/Enable GreenAP # 0 to disable, 1 to enable, default: 1 gEnableGreenAp=0 gPNOScanSupport=1 #Enable/Disable LPASS support # 0 to disable, 1 to enable gEnableLpassSupport=1 # Whether userspace country code setting shld have priority gCountryCodePriority=1 # Enable or Disable Multi-user MIMO # 1=Enable (default), 0=Disable gEnableMuBformee=1 # Enable support for TDLS # 0 - disable # 1 - enable gEnableTDLSSupport=1 # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall # initiate TDLS Discovery towards a peer whenever setup criteria (throughput # and RSSI) is met and then will initiate teardown when teardown criteria # (idle packet count and RSSI) is met. # 0 - disable # 1 - enable gEnableTDLSImplicitTrigger=1 # Enable TDLS External Control. That is, user space application has to # first configure a peer MAC in wlan driver towards which TDLS is desired. # Device will establish TDLS only towards those configured peers whenever # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS # when teardown criteria (idle packet count and RSSI) is met. However, # device will accept TDLS connection if it is initiated from any other peer, # even if that peer is not configured. # 0 - disable # 1 - enable # For TDLS External Control, Implicit Trigger must also be enabled. gTDLSExternalControl=1 # Enable support for TDLS off-channel operation # 0 - disable # 1 - enable # TDLS off-channel operation will be invoked when there is only one # TDLS connection. gEnableTDLSOffChannel=1 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gEnable2x2=1 gVhtRxMCS2x2=2 gVhtTxMCS2x2=2 #IPA config is a bit mask and following are the configurations. #bit0 IPA Enable #bit1 IPA PRE Filter enable #bit2 IPv6 enable #bit3 IPA Resource Manager (RM) enable #bit4 IPA Clock scaling enable #bit5 IPA uC ENABLE #bit6 IPA uC STA ENABLE #bit8 IPA Real Time Debugging gIPAConfig=0x7d gIPADescSize=800 # Enable TCP Segmentation Offload # 1 - enable 0 - disable TSOEnable=1 # Enable Generic Receive Offload # 1 - enable(default) 0 - disable GROEnable=1 # Enable HT MPDU Density # 4 for 2 micro sec ght_mpdu_density=4 # Enable flow steering to enable multiple CEs for Rx flows. # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. # Parallel Rx paths. # 1 - enable 0 - disable(default) gEnableFlowSteering=1 # Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND maxMSDUsPerRxInd=8 # Enable NUD tracking feature # 0 - disable(default),1 - trigger disconnect, 2 - trigger roaming, # 3 - trigger roaming, but if roam fails, disconnection gEnableNUDTracking=3 ################ Datapath feature set End ################ ################ NAN feature set start ################### # Enable NAN discovery (NAN 1.0) # 1 - enable 0 - disable(default) gEnableNanSupport=1 # Enable NAN Datapath genable_nan_datapath=1 ################ NAN feature set end ##################### hostscan_adaptive_dwell_mode=1 #disable probe request deferral oce_enable_probe_req_deferral=0 # set modulated DTIM interval gEnableModulatedDTIM=3 gMaxLIModulatedDTIM=3 # groam_dense_rssi_thresh_offset - Sets dense roam RSSI threshold diff groam_dense_rssi_thresh_offset=10 # Dense traffic threshold in kBps gtraffic_threshold=50 # Enable/Disable the Motion Aided Wireless Connectivity # based NLO using this parameter mawc_nlo_enabled=0 #Enable host side recovery gEnableSelfRecovery=1 #enable/disable FT open feature enable_ftopen=0 # This ini is used to allow STA+SAP SCC on LTE coex channel # 0 - Disallow STA+SAP SCC on LTE coex channel # 1 - Allow STA+SAP SCC on LTE coex channel g_sta_sap_scc_on_lte_coex_chan=1 drop_bcn_on_chan_mismatch=0 # Enable/Disable rtt sta mac randomization enable_rtt_mac_randomization=1 #Enable/Disable SNR monitoring gEnableSNRMonitoring=1 # WLM latency Enable wlm_latency_enable=1 # WLM flags setting for ultralow level, bit9 for BMPS disabled wlm_latency_flags_ultralow=0x3 # Enable ETSI SRD channels by Xiaomi. Qualcom default value is disable etsi13_srd_chan_in_master_mode=1 # Allow STA+SAP SCC on DFS channel with master mode support disabled g_sta_sap_scc_on_dfs_chan=2 # HTC Credit count for WMI operation # 1 to serialize the WMI commands # 0 default works with FW advertised credits, 2 credits usually gWmiCreditCount=1 # Enable enhanced ACS acs_with_more_param=1 # bits 0-3: rssi weight # bits 4-7: bss count weight # bits 8-11: noise floor weight # bits 12-15: channel free weight # bits 16-19: tx power range weight # bits 20-23: tx power throughput weight # bits 24-31: reserved AutoChannelSelectWeight=0x00fafafa # Enable/Disable broadcast TWT bcast_twt=1 # Enable broadcast logging to the userspace entities gMulticastHostFwMsgs=1 # Disable packetlog explicitly gEnablePacketLog=0 # Set IPA bandwidth levels in mbps gIPALowBandwidthMbps=100 gIPAMediumBandwidthMbps=400 gIPAHighBandwidthMbps=800 # Add another interface while driver load gEnableConcurrentSTA=wlan1 #max time for active 2G channel scan. #if set to zero, gActiveMaxChannelTime is used for 2G channel scan. active_max_channel_time_2g=0 #Enable to give higher priority for 5g scc than dbs g_prefer_5g_scc_to_dbs=8 # Enable/Disable LPRx gEnableLPRx=0 gActiveUcBpfMode=0 gActiveMcBcBpfMode=1 force_start_sap=1 # Assoc failure timeout value assoc_failure_timeout=5000 # Feature runtime PM: START gRuntimePM=2 gRuntimePMDelay=500 # Feature runtime PM: END #Idle Monitor Roaming: START enable_idle_roam=true idle_roam_min_rssi=-65 #Idle Monitor Roaming: END gindoor_channel_support=1 np_chan_weight=0x1 #roaming more like 5G and also not HE cap chan_width_weightage=5 he_caps_weightage=1 chan_band_weightage=5 END # Note: Configuration parser would not read anything past the END marker